指纹锁操作说明书 operation instruction of fingerprint lock1， 首次使用（任意手指均可开门）I.first time open(any fingerprint can open) 按下手指，听“嘀”提示声，指纹采集器白色背光亮起Press your finger, you will hear a buzzer notice, white color backlightinf from fingerprint acquisition machine. 按压指纹，听到“嘀嗒嘀”的开门提示音，同时“OK”点亮，电磁铁吸合,5s 后电磁铁释放，系统退出小箱子电机转动开门)input fingerprint, you will hear 3 times notice of beep, “OK”signal lightening, the door will open automatically by a motor drive.2， 指纹登记（指纹容量 30枚）在所有指示灯熄灭时，按一下“绿色”按钮，听到“嘀”的短音，指纹采集器白色背光亮起此时在采集器位置居中长按手指，听到“嘀“的一声长音，注册成功，同时“OK”点亮。
Fingerprint registeringStep 1: When all signal lights goes out, press BLUE button, you will hear a short “beep” notice, power signal lightening, then fingerprint acquisition machine lightingStep 2: Press your finger into middle of the fingerprint acquisition window for seconds, when you hear a long “beep” notice, that means register new fingerprint successfully, at the same time,“OK” signal displaying on the screen.3， 指纹开门 按下手指，听到“嘀”的提示声，指纹采集器白色背光亮起 按压指纹，听到“嘀嗒嘀”的开门提示音，同时“OK”点亮，电磁铁吸合,5s 后电磁铁释放，系统退出。
小箱子电机转动开门) 如果识别不成功，则会听到“嘀嘀嘀”的三声急促短音， “NO”同时点亮；如连续3次识别不成功,系统退出，所有指示灯熄灭，报警响起，持续 60秒 在报警过程中，只有输入正确指纹，才能解除报警，或者时间到后自动解除E. Use fingerprint to open Press your finger onto the fingerprint acquisition window, when hear a “beep” notice, power supply signal lights up, white dis[laying on fingerprint acquisition window. Input registered fingerprint, hear dick notice, “OK” signal lightening(the door will open automatically for small sate by a motor drive.)If it fail to recognize fingerprint, the system will give 3 rapid “beep” with NO button lighteningIf it fail to recognize fingerprint for 3 times continuously, the system will back off automatically, all signal lights go out with 60 seconds alarm.During alarm, only inputting right fingerprint can remove alarm or when the alarm finish itself.4， 删除所有指纹 在所有指示灯熄灭时，并且系统未报警时，按住“红色”按钮（不要松开） ，两秒后，听到“嘀”的一声长音， “OK”点亮，删除成功。
How to delete fingerprintAll signal lights go out and the system do not give an alarm, press the red button , 2 seconds later, you will hear a long “ticking” with OK signal on, that means delete fingerprint successfully. 5， 震动报警 按一下“红色”按钮，听到“嘀嗒嘀”的提示音，震动开启；听到“嘀”的提示音，震动关闭 （空指纹不开启，换电池后需重新设置）How to set vibration alarmPress the red button one time, you will hear a long beep notice, that means vibration alarm get started.you need set again if replace battery.6， 欠压 当电源电压低于 5 V(正负 0.2V)时，在使用的过程会出现“嘀嘀嘀”的报警音，同时“电量不足”点亮。
Low voltageWhen the voltage of power is lower than 5V, you will hear an alarm of rapid buzzer, please replace the batteries asap.7， 关门（小箱子） 按住关门开关，电机反转关门How to close safe(for small safe)Press close button, the motor will reverse to close the door。