《路由交换技术--综合组网课程设计》由会员分享，可在线阅读，更多相关《路由交换技术--综合组网课程设计（8页珍藏版）》请在金锄头文库上搜索。
1、1. 拓扑图：2.2. 配置OSPF(1) Router0Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 0.255.255.255 area 0Router(config-router)#network 2.1.1.0 0.0.0.255 area 0Router(config-router)#network 192.168.3.0 0.0.0.255 area 0(2) Router1Router(config)#router ospf 1Router(config-router)#network 2.1
2、.1.0 0.0.0.255 area 0Router(config-router)#network 11.0.0.0 0.255.255.255 area 0Router(config-router)#network 192.168.2.0 0.0.0.255 area 0(3) Router2Router(config)#router ospf 1Router(config-router)#network 11.0.0.0 0.255.255.255 area 0Router(config-router)#network 172.16.0.0 0.0.255.255 area 0Route
3、r(config-router)#network 192.168.1.0 0.0.0.255 area 0(4) Router3Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 0.255.255.255 area 0Router(config-router)#network 172.16.0.0 0.0.255.255 area 0(5)测试从Router0 ping Router 2Router#ping 172.16.0.1Type escape sequence to abort.Sending 5,
4、100-byte ICMP Echos to 172.16.0.1, timeout is 2 seconds:!Success rate is 100 percent (5/5), round-trip min/avg/max = 62/62/63 ms(6) 从Router 1 ping Router 3Router#ping 10.0.0.2Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 10.0.0.2, timeout is 2 seconds:!Success rate is 100 percent (
5、5/5), round-trip min/avg/max = 47/53/63 ms3. 配置PPP PAP双向认证（Router0、Router1）Router0配置：Router(config)#username 123 password 456Router(config)#inter s1/0Router(config-if)#encapsulation pppRouter(config-if)#ppp authentication papRouter(config-if)#ppp pap sent-username 111 password 222Router1配置Router(con
6、fig)#username 111 password 222Router(config)#inter s1/0Router(config-if)#encapsulation pppRouter(config-if)#ppp authentication papRouter(config-if)#ppp pap sent-username 123 password 4564. 配置DLCI帧中继Router3配置Router(config)#inter s1/0Router(config-if)#no ip addressRouter(config-if)#encapsulation frame
7、-relayRouter(config-if)#inter s1/0.1 multipointRouter(config-subif)#ip address 192.168.4.1 255.255.255.0Router(config-subif)#frame-relay map ip 192.168.4.2 502 broadcast Router(config)#inter s1/0.2 point-to-point Router(config-subif)#ip address 192.168.5.1 255.255.255.0Router(config-subif)#frame-rel
8、ay interface-dlci 504Router4、Router5配置Router(config)#inter s1/0Router(config-if)#ip address 192.168.4.2 255.255.255.0Router(config-if)#encapsulation frame-relay Router(config)#inter s1/0Router(config-if)#ip address 192.168.5.2 255.255.255.0Router(config-if)#encapsulation frame-relay 帧中继配置测试从Router3
9、ping Router4和Router5Router#ping 192.168.4.2Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 192.168.4.2, timeout is 2 seconds:!Success rate is 100 percent (5/5), round-trip min/avg/max = 47/59/63 msRouter#ping 192.168.5.2Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to
10、192.168.5.2, timeout is 2 seconds:.!Success rate is 80 percent (4/5), round-trip min/avg/max = 46/55/63 ms5.DHCP：1.为本地网段PC动态分配网络参数，FTP服务器动态分配固定地址2.为外部网段动态分配网络参数Router6配置如下：Router(config)#ip dhcp pool 1Router(dhcp-config)#network 192.168.1.0 255.255.255.0Router(dhcp-config)#default-router 192.168.1.1
11、Router(dhcp-config)#dns-server 192.168.3.2Router(dhcp-config)#exitRouter(config)#ip dhcp pool 2Router(dhcp-config)#network 192.168.2.0 255.255.255.0Router(dhcp-config)#default-router 192.168.1.1Router(dhcp-config)#dns-server 192.168.3.2FTP服务器获取成功PC2PC36. Router1作为vlan间路由，switch0作为VTP服务器，PC0和PC1通过Rou
12、ter6获得IP地址Router1：Router(config-if)#inter f0/0.2Router(config-subif)#encapsulation dot1Q 2Router(config-subif)#ip address 192.168.2.1 255.255.255.0Router(config-subif)#no shutRouter(config-subif)#inter f0/0.3Router(config-subif)#encapsulation dot1Q 3Router(config-subif)#ip address 192.168.10.1 255.2
13、55.255.0Router(config-subif)#no shutRouter(config)#ip forward-protocol udpRouter(config)#inter f0/0.2Router(config-subif)#ip helper-address 192.168.1.2Router(config-subif)#inter f0/0.3Router(config-subif)#ip helpRouter(config-subif)#ip helper-address 192.168.1.2Switch0：Switch(config)#vlan 2Switch(co
14、nfig-vlan)#exitSwitch(config)#vlan 3Switch(config-vlan)#exitSwitch(config)#inter f0/1Switch(config-if)#switchport mode trunk Switch(config)#inter f0/2Switch(config-if)#switchport mode trunk Switch(config-if)#inter f0/3Switch(config-if)#switchport mode trunk Switch1：Switch(config)#inter f0/1Switch(co
15、nfig-if)#switchport mode trunk Switch(config-if)#inter f0/2Switch(config-if)#switchport mode trunk Switch(config-if)#inter f0/3Switch(config-if)#switchport access vlan 2Switch2：Switch(config)#inter f0/1Switch(config-if)#switchport mode trunk Switch(config-if)#inter f0/2Switch(config-if)#switchport mode trunk Switch(config-if)#inter f0/3Switch(config-if)#switchport access vlan 3Router6：Router(config)#ip dhcp pool 3Router(dhcp-config)#network 192.168.10.0 255
