《sl500采煤机技术规格》由会员分享，可在线阅读，更多相关《sl500采煤机技术规格（56页珍藏版）》请在金锄头文库上搜索。
1、SL500采煤机技术规格Eickhoff SL 500 AC Shearer Loader Specification艾柯夫SL 500交流采煤机技术规格Shearer Loader General采煤机整机Machine Model型号Eickhoff SL 500 ACTotal power installed总装机功率1915 kWVoltage电压3.3 kV, + 10%, -20%Capacity (peak cutting) 产量（最高产量）2700 t/h*Cutting Power截割功率2 x 750 kWHaulage Power牵引功率2 x 90 kWMaximum
2、haulage pull最大牵引力771 kNMaximum haulage speed最大牵引速度30.2 m/minHydraulic Drive Power泵电机功率35 kWLumpbreaker Power破碎功率200 kWCutting height采高app. 约5000 mmUndercut depth卧底量app. 约415 mmMachine height from floor机身高度app. 约 2041 mmClearance for coal passing过煤口高度app. 约780 mmDistance between drum center两滚筒中心距1330
3、0 mmDistance between haulage (sprockets) 牵引齿轨轮间距6190 mmCutting drum diameter滚筒直径2300 mmCutting drum width滚筒宽度900 mmCutting depth截深800 mmDrum speed滚筒转速23 r.p.m.Maximum cutability of mineral最大截割硬度up to可达100 Mpa*Haulage system牵引系统Eicotrack 2000 or similar销排系统或类似Rack wheel齿轨轮Eicotrack 2000 or similar销排系
4、统或类似Machine weight机器重量app. 约100 tNoise level噪音等级approx. 约80 dB (A)Face gradient in conveyor direction工作面纵向倾角max 10 without brakes最大10时不带制动器Face gradient transverse to conveyer工作面横向倾角max 10最大10 PF 6 / 1142型前刮板运输机No. 序 号Item项 目 名 称Technical Specification技 术 指 标1.General概述1.1Type and standard规格型号PF 6/1
5、1421.2Manufacturer生产厂家Bucyrus Europe GmbH比塞洛斯欧洲有限公司1.3Transport capacity(t/h) 运输能力(t/h)2500 t/h1.4Design length（m）设计长度（m）320 m (for calculation of max. required drive power 用于计算所需最大功率)1.5Laying length(m) 铺设长度(m)300 m (as defined by the enduser 用户要求)1.5aOrdered length (m) 订货长度300 m (quoted length 投标长
6、度)1.6Dimension of line pan (mm)中部槽外形尺寸 (mm)1756 mm1.7Structure characters of line pan 中部槽结构特点Welded structure with rolled profiles 轧制槽邦钢，焊接型式1.8Connecting method of line pan 中部槽联接方式Dogbone哑铃销1.9Applicable face inclination ()适应的工作面倾角()+/- 101.10Applicable entry inclination ()适应的工作面走向倾角()+/- 61.11Powe
7、r supply voltage /allowed change range (V) 供电电压/允许波动范围(V)3.3 kV1.12Power supply frequency (Hz)供电频率(Hz)50 Hz1.13Total installed power (kw)总装机功率(kW)2x1050kW1.14Chain speed(m/s) 链速(m/s)1.53 m/s1.15Spacing of flight bar (m)刮板间距(m)876 mm1.16Discharge method卸载方式Overhead discharge端卸1.17Discharge height（mm）
8、卸载高度（mm）Approx. 约1200 mm1.18Soft-start mode软启动方式CST1.19Layout of the drive devices 驱动装置的布置方式Parallel平行布置1.20Shearer haulage method 采煤机牵引轨道型式Jumbotrack 20001.21Normal start under the full load (Yes/No) 在满载条件下能否正常启动Yes是1.22Cooling method and parameters 冷却方式及参数Water cooled水冷1.23Noise（dB）噪音（dB）851.24Ove
9、rhaul period大修周期(Mt)Refer to warranty section参见质保期条款1.25Total weight(kg) 总重量(kg)t.b.a.1.26The whole machine warranty period (Mt)整机质保期(Mt)Refer to warranty section参见质保期条款1.27The whole machine service life(Mt)整机寿命(Mt)Refer to warranty section参见质保期条款2Chain tensioning device链条自动张紧装置2.1Type型式PM4 controll
10、ed 由PM4控制装置控制2.2Type of control devices控制装置形式Pressure, stroke measurement 监测压力、行程数据2.3Structure and principle结构原理Hydraulic cylinder in tg drive通过机尾驱动部液压油缸作用3Chain sprocket链轮3.1Structure type结构形式Cast, split sprocket 铸造、剖分式链轮3.2Tooth number齿数73.3Tooth surface hardness齿面硬度50 -55 HRC3.4Weight (kg) 重量(kg
11、)900 kg3.5Life (Mt) 寿命(Mt)Refer to warranty section参见质保期条款4Line pan（different line pans to be described respectively）溜槽（各种溜槽分别叙述）4.1Structure type结构形式PF 6/11424.2Outer dimension(LWH) 、inner width（ mm）外形尺寸(LWH) 、内宽（ mm）1836 x 1804 x 624 mm4.3Connecting mode连接方式Dogbone 哑铃销4.4The vertical applicable an
12、gle of the connecting part ()连接处垂直方向适应角度()Approx. 约+/- 3.64.5The horizontal applicable angle of the connecting part ()连接处水平方向适应角度()Approx.约 +/- 14.6Deck plate thickness (mm)中板厚度(mm)30+254.7Deck plate material中板材料S690Q + HDX 4004.8Bottom plate thickness (mm)底板厚度(mm)30 mm4.9Bottom plate material底板材料HD
13、X 4004.10Connecting device strength (kN)连接装置强度(kN)4500 kN4.11Type of bottom chain check device 底链检查装置形式Inspection holes in gobside profile each pan每节溜槽槽邦老塘侧设有观察孔One out of each 5 pans has inspection door.5每6槽中含一节观察槽All face end rerouting pans have inspection door所有端头及变线槽均为观察槽4.12weight(kg) 溜槽重量(kg)A
14、pprox. 约2620 kg4.13life(Mt) 溜槽寿命(Mt)Refer to warranty section参见质保期条款5Chains and flight链条和刮板5.1Chain type链条型号TIB 42x1465.2Chain manufacturer链条制造厂商Thiele5.3Chain link type链环型式Welded 焊接5.4Chain speed(m/s) 链速(m/s)1.53 m/s5.5Chain link specification (DT mm)链环规格(DT mm)42x146 mm5.6Minimum breaking force of chain (kN)链条最小破断力(kN)2220 kN5.7Chain material：链条材料：DIN 171155.8Unit chai
