《[2017年整理]钻井常用英汉对照表1》由会员分享，可在线阅读，更多相关《[2017年整理]钻井常用英汉对照表1（7页珍藏版）》请在金锄头文库上搜索。
1、 钻井事业部“三基”工作手册钻井常用英汉对照表第 1 页 共 7 页Drilling-COSL打捞工具和常用词语spear 打捞矛 back pressure 回压side wall core 井壁取芯 drill out cement 钻水泥塞casing scraper 套管清刮器 explosive 炸药mill 磨鞋 squeeze cement 挤水泥die stamp 铅印 fast line spooler 快绳排绳器pin tap 公锥 shallow gas 浅层气box tap 母锥 panels 面板packer 封隔器 bridge plug 桥塞opener 扩眼器
2、well kick and 50BBLs pits gain 井涌增量 50桶junck sub 打捞杯 kelly guard 方钻杆保护接头fishing over shot 打捞筒 blow out 井喷cutter 割刀 guideline 导向绳blades 刀臂 guide rail 导轨pony D.C 短钻鋌 pick up weight 上提重量pup joint 短钻杆 sluck off weight 下放重量slick M.D.C 光滑防磁钻鋌 rotating weight 总重量fishing neck 打捞短节 max torque 最大扭矩perforate 射
3、孔 rotating HRS 纯钻井时间no accident 无事故 total BHA length 总 BHA 长度HRS on swivel 水龙头时间 check crown o matic 检查防碰天车below jar W.T 震击器以下重量 total BHA weight 总 BHA 重量HRS on jar 震击器时间 held safety meeting on rig floor 钻台举行安全会seal assembly 密封总成 wear bushing 抗磨补芯total mud cost 泥浆总消耗量 bridge crane of the BOP BOP 叉车c
4、entrifugal pump 灌注泵 liner 尾管brine 饱和盐 Wash pipe packing 冲管盘根sub sea camera 水下电视 sand traps 沉沙池core barrel 岩芯筒 compensator 补偿器travelly block 游车 crown block 天车Draw works 钻井绞车 stabilizer 扶正器port 左舷 starboard 右舷annular prevent 万能防喷器 choke/kill line 阻流和压井管线 钻井事业部“三基”工作手册钻井常用英汉对照表第 2 页 共 7 页Drilling-COSLs
5、hear ram 剪切闸板 choke manifold 阻流管汇trip tank 计量罐 gas peak 气测值plug back 打水泥塞 dart sub 投入式止回阀nozzle 水眼 jetter 喷射冲洗器boost line 加速管线 core point 取芯点marine swivel 水下水龙头 trip gas 后效气prepare 准备 after effect 后效break CIRC 短时循环 mud cleaner 泥浆清洁器degasser 除气器 desilter 除泥器desander 除沙器 prior/before 在之前shale shaker 震
6、动筛 helicopter 直升飞机gas cut mud 气侵泥浆 special tool 特殊工具open hole 裸眼 No.4 guide line brocken 四号导向绳断掉tubing 油管 fix 修理testing 测试 caving 垮塌plugged bit 泥包钻头 D.c twist off 钻鋌折断well off set 井口位移 tugger 气动绞车recover survey 回收测斜仪 pitch 纵摇rig heading 平台首向后 sweel 涌wind speed 风速 wave 浪roll 横摇 heave 升沉visible 能见度 di
7、r 方位钻井常用短语Last anchor on rack at 0600HR 六点最后一个锚上架Start of contract at 1530HR 下午三点半合同开始End of contract at 0300HR 早上三点合同结束Rig on tow 平台拖航Rig arrived well location at 1000HR 早上十点到达井位Run anchors and first anchor on bottom at 1100HR 抛锚。第一个锚 11 点到底Ballast rig to 70ft draft 压载到 70 英尺deballast rig 平台卸载adjus
8、t well location with pull No .1 and No.2 anchors gain拉 1 和 2 号锚调整井位anchor tension test No.3 and No4-ok 1 和 2 号锚张力试验-OKwait slack tide 等待平潮replace upper felly cock 替换方钻杆上阀 钻井事业部“三基”工作手册钻井常用英汉对照表第 3 页 共 7 页Drilling-COSLspuded time 开钻时间arrived time 到达井位时间drill 36hole from 120m to 200m & pump 50bbls mud
9、 each connection and ream each connection once钻 36井眼从 120 米至 200 米 ,每接一拄前滑眼一次并泵入 50 桶泥浆open 17-1/2hole from 250m to 500m 用 17-1/2钻头扩眼从 250 米至500 米leak off test at 500m.MW 1.2SG leak off 625psi 破裂试验.井深 500 米、泥浆比重1.2SG.泄漏压力为 625PSIream hole from 450m to 500m 倒划眼从 450 米至 500 米core drill from 1300m to 1
10、320m 取芯钻进从 1300 米至 1320 米collect/remove core and service core equipment 收集/甩下岩芯并包装处理sweep hole with 100bbl HI-VIS mud 用 100 桶高粘泥浆清洗井slug the hole with viscous mud 泵送一段稠泥浆进井pump 6000stks HI-VIS mud 泵 6000 冲高沾泥浆circulate and working on pipe 循环并活动钻杆circulate and wash from 100m to 200m 循环清洗 100 米至 200 井
11、段circulate bottom up 循环井底出来circulate for sample 循环取样flow check at 2300m due to drilling break 流量观察因钻至 2300 米时突变circulate for flow check 循环观察circulate and condition mud 循环处理泥浆reverse circulate 反循环pooh no rotary and no drag 起钻不用转盆也不拖挂run in W/26 x 36BHA tag seabed 117m. 下 26领眼钻头和 36扩眼器至117 米探海底泥面RIH t
12、o wipe trip 下钻通井RIH to tag top of cement at 1000m 下钻探水能面在 1000 米处short trip over pull 50klbs 短起过提 50 千磅make up new bottom hole assy 组合新的下部钻具drop survey pump slug and POOH 投测打重泥浆.起钻retrieve/return survey 回收测斜仪inside BOP drill at casing shoe 在套管鞋进行防喷演习POOH circ & fill annular W/TR.TK.P no good. Suspec
13、t mud problems. W/pull out every 5 Stands&fill a time ok起钻灌浆不正常,怀疑是泥浆问题.每起五柱灌浆-正常POOH due to change bit 因要换钻头所以起钻POOH due to lost pump pressure suspect washout D.C 泵压下降起钻,怀疑钻鋌刺漏POOH due to plan change 计划改变起钻POOH for changing bottom hole assy 起钻更换下部钻具组合POOH wet pipe and no slug 起钻喷泥浆因没打重泥浆 钻井事业部“三基”工
14、作手册钻井常用英汉对照表第 4 页 共 7 页Drilling-COSLPOOH no rotary 起钻不转转盆POOH and tight hole at 2500m max over pull 100klbs 起钻在 2500 米处遇阻最大过提100 千磅slip and cut off drill line 110feet 滑移切割钻井大绳 110 英尺RIH at casing shoe then service rig 下钻至套管鞋后保养钻机POOH casing shoe adjust break&wait hole stabilize 起钻至套管鞋待井稳定后调整剎带pull b
15、ack 5 stands5drillpipe and rack back derrick 起出 5 柱 5钻杆并立回井架attempt retreive9-5/8wire bushing but fail 试图回收 9-5/8抗磨补芯没成功50bbls pit gain shut in well observe pressure 0-SIDPP 175psi SICP50 桶泥浆增量,关井后钻杆压力为0,套管压力为 175psikill well as NHWOC,s requst 按西部公司压井程序压井CIRC and COND .mud.CIRC out gas show from ret
16、urns max gas 1700units循环处理泥浆,最大气测值为 1700个单位D.P hang off on L.P.R.CIRC.through wide open choke while W.T up mud钻杆悬挂在下闸板,循环通过全开阻流阀同时加重泥浆moniton will on trip tank 3bbls gain in 2HRS 在泥浆计量罐观察两小时有 3 桶的增量.circulate and inspect due to pressure lost 200psi 循环检查因泵压下降 200PSIcirc through choke holding 600psi back press on annu
