《从交换机上下载app文件并拷至另一台交换机》由会员分享，可在线阅读，更多相关《从交换机上下载app文件并拷至另一台交换机（3页珍藏版）》请在金锄头文库上搜索。
1、一，开启远程交换机的ftp服务器（以172.19.110.4为例）：首先登录172.19.110.4然后进行配置xsss10#4ftp server enable开启ftp服务器 % FTP server has been startedxsss10#4local-user fdp创建或进入fdp用户模式xsss10#4-luser-fdpservice-type ftp设置fdp用户可以使用ftp服务xsss10#4-luser-fdppassword simple fdp为用户fdp配置密码，也为fdp二，在本地PC上下载app文件进入控制台，如下进行操作，黄色部分为自己输入的命令C:Do
2、cuments and SettingsAdministratorftp 172.19.110.4Connected to 172.19.110.4.220 FTP service ready.User (172.19.110.4:(none): fdp331 Password required for fdp.Password:230 User logged in.ftp dir200 Port command okay.150 Opening ASCII mode data connection for *.-rwxrwxrwx 1 noone nogroup 442799 Jun 02
3、2005 wnm2.2.2-0004.zip-rwxrwxrwx 1 noone nogroup 3478995 Jun 02 2005 E050-VRP310-r0029-150-a.bin-rwxrwxrwx 1 noone nogroup 8 Mar 24 00:11 snmpboots-rwxrwxrwx 1 noone nogroup 5015 Dec 04 23:40 vrpcfg.txt226 Transfer complete.ftp: 收到 291 字节，用时 0.00Seconds 291000.00Kbytes/sec.ftp get E050-VRP310-r0029-
4、150-a.bin200 Port command okay.150 Opening ASCII mode data connection for E050-VRP310-r0029-150-a.bin.226 Transfer complete.ftp: 收到 3478995 字节，用时 13.20Seconds 263.50Kbytes/sec.ftp三，将app文件上传至其他交换机进入控制台，如下进行操作，黄色部分为自己输入的命令启动交换机，在启动界面按Ctrl+B，进入Boot Menu，密码为空，按照命令一步步操作Starting. * * * * Quidway E050 BOOT
5、ROM, Version 150 * * * * Copyright(C) 2002-2004 by HUAWEI TECHNOLOGIES CO.,LTD. Creation date : Mar 25 2004, 14:50:01 CPU type : MPC8241 CPU Clock Speed : 200MHz Memory Size : 64MB Initialize E050 main board.OK! SDRAM selftest.OK! FLASH selftest.OK! CPLD selftest.OK! Switch chip selftest.OK! Switch
6、SDRAM selftest.OK! Subslot1/1 has 1000BASE-T GT module Subslot2/1 has no module PHY selftest.OK! Please check port leds.finished! The switch Mac is: 00E0-FC6D-3B14Press Ctrl-B to enter Boot Menu. 0Password: BOOT MENU1. Download application file to flash2. Select application file to boot3. Display al
7、l files in flash4. Delete file from flash5. Modify bootrom password0. RebootEnter your choice(0-5): 1Please set application file download protocal parameter:1. Set TFTP protocol parameter2. Set FTP protocol parameter3. Set XMODEM protocol parameter0. Return to boot menuEnter your choice(0-3): 3Pleas
8、e select your download baudrate:1: 96002: 192003: 384004: 576005: 115200*0: ReturnEnter your choice(0-5): 5Load file name :E050-VRP310-r0029-150-a.bin Are you sure to download file to flash?(Y/N)选择y，然后在SecureCRT软件的“选项”-“会话选项”-“串行”，将波特率设为“115200”回到交换机配置界面下按下回车，出现loadingCCCCCCCCCCCCCC时，在SecureCRT软件的“传输”-“发送XMODEM”里，选择要传输的app文件，这时会出现传输进度待传输完毕后，记得在SecureCRT软件的“选项”-“会话选项”-“串行”，将波特率设回“9600”
