《练习II-6(模态分析-分块兰索斯法-U-型支架)》由会员分享,可在线阅读,更多相关《练习II-6(模态分析-分块兰索斯法-U-型支架)(10页珍藏版)》请在金锄头文库上搜索。
1、U-型支架,练习 6 模态分析 分块兰索斯法,January 30, 2001 Inventory #001444 W6-2,6. 模态分析 分块兰索斯法 U-型支架,说明 使用分块兰索斯法提取U型支架的前10阶模态。列出频率并画出整个模型的 von Mises 应力。画出第一阶模态,然后作动画显示。,January 30, 2001 Inventory #001444 W6-3,6. 模态分析 分块兰索斯法 U-型支架,荷载与材料特性,January 30, 2001 Inventory #001444 W6-4,6. 模态分析 分块兰索斯法 U-型支架,1. 按教师指定工作目录,用 “u-
2、bracket”作为作业名, 进入ANSYS. 2. 恢复数据库 “u-bracket.db1” : Utility Menu File Resume from 或用命令: RESUME,u-bracket,db1 3. 进入求解器,约束U型支架顶面(面17)上的所有自由度: Main Menu Solution -Loads- Apply -Structural- Displacement On Areas + 或用命令: /SOLU DA,17,ALL,January 30, 2001 Inventory #001444 W6-5,6. 模态分析 分块兰索斯法 U-型支架,4. 定义分析类
3、型为模态分析: Main Menu Solution -Analysis Type- New Analysis . 或用命令: ANTYPE,MODAL 5. 定义分析选项:Main Menu Solution Analysis Options No. of modes to extract = 10 No. of modes to expand = 10 Elcalc = Yes 或用命令: MODOPT,LANB,10 EQSLV,SPAR MXPAND,10,1,January 30, 2001 Inventory #001444 W6-6,6. 模态分析 分块兰索斯法 U-型支架:,6
4、. 存储数据库并开始求解: Pick the “SAVE_DB” button in the Toolbar (or select: Utility Menu File Save as Jobname.db) Main Menu Solution -Solve- Current LS 或用命令: SAVE SOLVE 7. 进入通用后处理器,列出10个频率: Main Menu General Postproc Results Summary 或用命令: /POST1 SET,LIST,January 30, 2001 Inventory #001444 W6-7,6. 模态分析 分块兰索斯法
5、 U-型支架,8. 对第一阶模态画出 von Mises 应力 : Main Menu General Postproc -Read Results- First Set Main Menu General Postproc Plot Results -Contour Plot- Nodal Solu . 或用命令: SET,1,1 PLNSOL,S,EQV,January 30, 2001 Inventory #001444 W6-8,6. 模态分析 分块兰索斯法 U-型支架,9. 画出下一阶模态的 von Mises 应力: Main Menu General Postproc -Read
6、 Results- Next Set Main Menu General Postproc Plot Results -Contour Plot- Nodal Solu . 或用命令: SET,NEXT PLNSOL,S,EQV,January 30, 2001 Inventory #001444 W6-9,6. 模态分析 分块兰索斯法 U-型支架,10. 对其它频率重复步骤 9,画出模态,观察 von Mises 应力: Main Menu General Postproc -Read Results- Next Set Main Menu General Postproc Plot Res
7、ults -Contour Plot- Nodal Solu . 或用命令: SET,NEXT PLNSOL,S,EQV 11. 画出包含未变形轮廓线的第一阶模态: Main Menu General Postproc -Read Results- First Set Main Menu General Postproc Plot Results -Contour Plot- Nodal Solu 或用命令: SET,FIRST PLNSOL,U,SUM,2,1,January 30, 2001 Inventory #001444 W6-10,6. 模态分析 分块兰索斯法 U-型支架,13. 作第一阶模态的动画: Utility Menu PlotCtrls Animate Mode Shape . 或用命令: PLDISP ANMODE,10,0.514. 存储数据库,退出 ANSYS: Pick the “QUIT” button inthe Toolbar 或用命令: SAVE FINISH /EXIT,