《外文文献及翻译：压缩机，泵，制冷工程》由会员分享，可在线阅读，更多相关《外文文献及翻译：压缩机，泵，制冷工程（20页珍藏版）》请在金锄头文库上搜索。
1、外文翻译第 1 页 共 21 页ChemicalChemical andand PetroleumPetroleum Engineering,Engineering, Vol.Vol. 40,40, Nos.Nos. 111112,12, 20042004 COMPRESSORS,COMPRESSORS, PUMPS,PUMPS,REFRIGERATIONREFRIGERATION ENGINEERINGENGINEERINGUPDATINGUPDATING PISTONPISTON PUMPSPUMPS FORFOR OILOILPRODUCTIONPRODUCTIONB.B. S.S. Z
2、akharov,1Zakharov,1 G.G. N.N. Sharikov,2Sharikov,2andand E.E. G.G. Kormishin2Kormishin2The three-plunger acid treatment pump SIN32 and the two-cylinder double-acting pump NPTs-32 with four working chambers (for cementing units) have been updated to control pump delivery. The fluid delivery diagrams
3、for pumps of various designs are examined and the test results are reported.In drilling and oil production, single-acting three-plunger (triplex) pumps or double-acting two-cylinder (duplex) pumps are used.In injecting reagents (clay drilling mud, water, cement, acid, etc.) into wells, depending on
4、the technology applied，it is required to inject the fluid in amounts ranging from the maximum to the minimum in a single operation. If the bed accepts the injected fluid well, it becomes necessary to maximize pump delivery for quick completion of the operation. If on the other hand, the bed does not
5、 accept the fluid well, it becomes necessary to reduce pump delivery so as to restrict the injection pressure to the safe limit. At present, because of wear of well (down-hole) equipment, the permissible injectionpressure is not higher than 1015 MPaThe delivery of a piston (reciprocating) or a plung
6、er (displacement) 外文翻译第 2 页 共 21 页type of pump can be controlled in the following ways: by installing several pumps with identical or different pumping capacities; by changing the drive rotation speed; by using cylinders (plungers) of the required size; by channeling a part of the fluid into a bypas
7、s; and by dismounting one or several valves.The first version is used essentially in drilling. In oil production, generally all versions are used either individually or in some combination.All pumping units designed for injection of various fluids (fluidal materials) for cementing, hydraulic formati
8、on fracturing, hydraulic sand-jet flushing of sand bridges, and other flushing operations in oil and gas wells are mounted on the chassis of motor vehicles (trucks), tractors, caterpillar (tracked) carriers, and specially made carriages.The operating parameters of the pumps (delivery and injection p
9、ressure) depend on the power of the drive and maximum and minimum speed of the engine and the pump. The pump delivery can be changed by changing the number of pump strokes without stopping the engine with the help of a gearbox (by gear shifting) and with stopping of the engine by installing cylinder
10、s of the required size. Replacement of the cylinders takes a lot of time and is not always possible in a continuous echnological process. In the existing pumping plants, the delivery variation range is inadequate. At the minimum rotation speed and cylinder diameter, the delivery remains extremely hi
11、gh, and for injecting the fluid into the bed the pressure has to be raised above what is permissible.外文翻译第 3 页 共 21 页Assigned by NGDU Zainskneft, kogermet carried out updating of two types of pumps, namely, SIN32 and NPTs-32.In the three-plunger (triplex) acid treatment pump SIN32, for reducing the
12、minimum delivery down to 1.0 m3/h,plungers having a diameter of 125 mm were replaced with plungers having a diameter of 55 mm. As a result, the theoretical pump delivery was reduced from 16 down to 3.3 m3/h. Further reduction of the pump delivery was achieved by reducing the rotation speed of the ve
13、hicle engine to the possible minimum (500600 rpm).Simultaneously with this, a new design of packing glands (sealing devices) of plungers of the UPN55 type was developed.It was based on Zakharov mechanical seal 1, which demonstrated high reliability and durability in sucker-rod (oil) pumps. The seali
14、ng units and the pistons with a diameter of 55 mm were made for the SIN32 pump by LKAMneftemash in Perm. Its finishing and testing were done by kogermet jointly with NGDU Zainskneft.The design of the UPN55-type plunger seal is shown in Fig. 1. The 外文翻译第 4 页 共 21 页combined seal consists of the main t
15、hreestage mechanical seal 4 and an elastic sealing collar 2. Each stage of the mechanical seal consists of ten rings that are elastically pressed against each other and simultaneously against the plunger surface. The rings are pressed against theplunger in pairs from the opposite sides. The next pai
16、r is turned relative to the preceding one by 90. The rings are pressed in the axial direction by rubber rings of round cross section and in the radial direction, by rubber girdles with eccentric collars. The plunger 5 is made of steel 45 and is chromium-plated and the sealing rings are of bronze. Threecartridges with mechanical seals were installed in the housing bore 3 with a clearance that helps self-centering of the seals relative to the plunger. The car
