《ABB直流调速 DCS400》由会员分享，可在线阅读，更多相关《ABB直流调速 DCS400（57页珍藏版）》请在金锄头文库上搜索。
1、ACS400ABB Automation ABB Comp_AC ACS400 OH 1 (57) 21/02/2000Code: Product introduction Content of the presentation: 内容简介2) Mechanics Ti = 2-5 min, Td = Ti/4 温度控制一般使用PID控制;放大倍数20-60; Ti = 2-5 min, Td = Ti/4Parameter 4004:to set the time constant of the filter to suppress the possible noisePID控制器-PID
2、ACS400ABB Automation ABB Comp_AC ACS400 OH 46 (57) 21/02/2000Code: PID-controller Scaling the actual valueA cooling system which feedback is temperature: - temperature 15 or lower = 0 - 4 mA - temperature 15 -35 = 4 - 20 mA - temperature 35 or higher = 20 mAScaling of the actual value (4009, 4010):
3、- MIN ACT1 is set to 0%(= 15 C) - MAX ACT1 is set to 100%(= 35 C)Scaling of the analogue input 2 (1304, 1305): - MINIMUM AI2 is set to 20%(the minimum value for the AI2 is 4 mA) - MINIMUM AI2 is set to 100%(the maximum value for the AI2 is 20 mA)Presettings (1103, 4006, 4007): (- Analogue input 1 se
4、lected for reference value) - Analogue input 2 (AI2) selected for the actual value feedback - Actual value 1 (ACT1) is used as such for the feedback0%100%ACT 1temperature15 C35 C4mA20 mAAI 1实际值的变比ACS400ABB Automation ABB Comp_AC ACS400 OH 47 (57) 21/02/2000Code: PID-controller Sleep functionActual v
5、alue 实际值Time 时间Wake-up leve唤醒等级Frequency 频率Sleep level (Hz)睡眠等级Stop 停止Start 起动t tdtdTime 时间td = sleep delayParameters 4013 - 4015Stand-by mode睡眠功能睡眠状态ACS400ABB Automation ABB Comp_AC ACS400 OH 48 (57) 21/02/2000Code: macros1. Factory default configuration工厂宏 缺省配置2. ABB standard general macro for Eur
6、opeABB 标准型 适于欧州的标准宏3. 3-wire push-button use3- 线型 按钮控制 4. Alternate alternating the direction交变型 交替变换转动方向5. Motor pot.meter ref. in- and decrease through Dis电动电位器型 数字信号来控制给定6. Hand-Auto two control modes (HVAC)手动/自动 两种外部控制模式7. PID-control closed loop control: pressure, flow .PID- 控制 闭环控制系统:压力,流量8. P
7、remagnetise for quick start预磁通型 适于要求快速起动 9. PFC for pump and fan泵和风机控制 用于泵和风机9 种预置宏ACS400ABB Automation ABB Comp_AC ACS400 OH 49 (57) 21/02/2000Code: Factory (0)Analog input 模拟输入 Frequency (AI1) 频率给定 (AI1) Digital inputs 数字量输入 Start / Stop (DI1) 起动/停止 Direction (DI2) 转向 Constant speed (DI3) 恒速 Ramp
8、pair 1/2 selection (DI5) 曲线1/2 选择 Analog output 模拟输出 Frequency (AO) 输出频率 (AO) Relay outputs 继电器输出 Fault (RO1) 故障(RO1) Running (RO2) 运行(RO2)For applications where no panel available or needed! 用于无控制盘的应用 Motor nominal values are 230/400V, 50 Hz and 1440rpm 电机额定值为230/400V, 50 Hz和1440rpm Signals scaled
9、according to 50 Hz 信号按50 Hz标称 Max output frequency 50 Hz 最大输出频率为50 Hz To activate US settings (factory (1) - 60Hz), DI4 needs to DI4为US设置 be connected to 24V 工厂宏(0)-50HZ 应用ACS400ABB Automation ABB Comp_AC ACS400 OH 50 (57) 21/02/2000Code: Analog input 模拟输入 Frequency (AI1) 频率给定 (AI1) Digital input 数字
10、量输入 Start / Stop (DI1) 起动/停止 Direction (DI2) 转向 Constant speed (DI3) 恒速 Constant speed (DI4) 恒速 Ramp pair 1/2 selection (DI5) 曲线1/2 选择 Analog output 模拟输出 Frequency (AO) 输出频率 (AO) Relay output 继电器输出 Fault (RO1) 故障(RO1) Running (RO2) 运行(RO2)General purpose macro for constant speed applications 一般用于恒速应
11、用场合ABB standardABB 标准宏ACS400ABB Automation ABB Comp_AC ACS400 OH 51 (57) 21/02/2000Code: Analog input 模拟输入 Frequency (AI1) 频率给定 (AI1) Digital input 数字量输入 Start (DI1) 起动 Stop (DI2) 停止 Direction (DI3) 转向 Constant speed (DI4) 恒速 Constant speed (DI5) 恒速Analog output 模拟输出 Frequency (AO) 输出频率 (AO) Relay o
12、utput 继电器输出 Fault (RO1) 故障(RO1) Running (RO2) 运行(RO2)For applications the drive is controlled using momentary push buttons本应用由不保持的按钮控制 3-Wire3- 线型ACS400ABB Automation ABB Comp_AC ACS400 OH 52 (57) 21/02/2000Code: Offers an I/O configuration that is adopted to a sequence of DI control signals when al
13、ternating the direction of rotation of the drive 提供当交替变换转动方向时DI顺序控制的I/O配置AlternateAnalog output 模拟输出Frequency (AO) 输出频率 (AO) Relay output 继电器输出Fault (RO1) 故障(RO1)Running (RO2) 运行(RO2)Analog input 模拟输入 Frequency (AI1) 频率给定 (AI1) Digital input 数字量输入 Start / Stop (DI1) 起动/正转 Direction (DI2) 起动/反转 Const
14、ant speed (DI3) 恒速 Constant speed (DI4) 恒速 Ramp pair 1/2 selection (DI5) 曲线1/2 选择 交变型ACS400ABB Automation ABB Comp_AC ACS400 OH 53 (57) 21/02/2000Code: Cost effective interface for PLCs that vary the speed of the drive using only digital signals 提供了一种仅使用数字信号来控制传动变速的，与PLC相连的经济接口Motor potentiometerAnalog input 模拟输入 Frequency (AI1) 频率给定 (AI1) Digital input 数字量输入 Start / Stop (DI1) 起动/停止 Direction (DI2) 转向 Reference up (DI3) 升速 Reference down (DI4) 降速 Consta
