《多功能环氧涂料ih38》由会员分享，可在线阅读，更多相关《多功能环氧涂料ih38（2页珍藏版）》请在金锄头文库上搜索。
1、 多功能环氧涂料IH38多功能环氧涂料IH38 Multi-purpose Epoxy Coating IH38 Multi-purpose Epoxy Coating IH38 上海日神精细涂料有限公司ISO9001认证企业 上海日神精细涂料有限公司ISO9001认证企业 产品说明产品说明 Description IH38是一种多用途高固体份厚浆环氧漆，可与多种面漆包括聚氨脂及丙烯酸类面漆配套使用。可自作防锈底漆， 适用于各种底材。也可在腐蚀性环境下使用作为优良的车间底漆。IH38具有优异的耐化学品性，适合浸泡环境下 使用。对无机硅酸锌具有极好的附着力。施工方便，表面处理不大理想时也可施工。
2、成膜范围大。 IH38 is a mult-purpose hi-build epoxy coating, which may be primer for durable systems with wide range of topcoats, including polyurethanes and acrylics. Excellent shop primer for corrosive service. Suitable for immersion service. Outstanding chemical and weather resistance. Excellent adhesio
3、n to inorganic zinc silicate. Easy application. Compatible with a variety of substrates and surface preparations. Wide film build range. 主要特性主要特性 Outstanding Characteristics IH38是一种高性能涂料,形成一种坚韧、耐磨、持久的漆膜。可牢固附着于裸露或已涂漆的钢质表面,以及无机硅 酸锌涂覆的表面,适用于新建筑维修及现场保养工程。IH38还可黏附于完整无损的涂漆表面和牢固的锈斑上,也可 用于修补自身或无机硅酸锌的底漆。 IH3
4、8 使用方便,可用各种喷涂方法施工,形成光滑,迅速干燥的漆膜。它可在不超过60的条件下连续在盐水和淡 水中使用,并可用作贮存碱液、盐溶液、石油燃料、排污物以及某些化学品的贮槽衬里。IH38可作为某些贮槽衬 里配套的底漆。除钢质表面外,还可施涂在铝、不锈钢、镀锌铁、混凝土以及以前已涂漆的表面上。 IH38 is a high performance epoxy coating forming a tough, abrasion-resistant, durable film. It adheres strongly to bare steel, coated and inorganic zinc
5、 silicate primed surfaces on new construction, repair and field maintenance projects. IH38 will also adhere to intact painted surfaces and tight rust and may be used to repair itself or inorganic zinc silicate primers. IH38 is user-friendly and can be applied by a variety of methods to produce a smo
6、oth, fast-drying film. it is suit able for immersion in both salt and fresh water at temperatures up to 60, continuous and can be used as a tank lining for alkaline and salt solutions, petroleum fuels, sewage waste and certain chemicals. It may also be applied over aluminum, stainless steel, galvani
7、zing, concrete and previously coated surfaces in addition to steel. 技术数据技术数据 Technical Data 漆 面: Finish: 平光 Flat 颜 色: Colors: 色卡上任选 Colors are available on color card 体积固体含量: Volume solids: 68%3% 理论涂布率: Theoretical spreading rate:6.5米2/升 (100微米干膜计) 5m2/L (100micron DFT) 耐 温： Temperature resistance:
8、最大（干燥）：121 Maximum (dry)： 闪 点: Flash point: 53 比 重: Specific gravity: 约1.35千克/升 Approx. 1.35 kg / L 指 触 干: Dry to touch: 约2小时 20 Approx. 2 hours 施工详述施工详述 Application Details 固 化 剂: Curing agent: H375 多功能环氧涂料IH38多功能环氧涂料IH38 Multi-purpose Epoxy Coating IH38 Multi-purpose Epoxy Coating IH38 上海日神精细涂料有限公
9、司ISO9001认证企业 上海日神精细涂料有限公司ISO9001认证企业 混合比例: Mixing ratio: 基料IH38:固化剂H375 =1:1 (体积比) Base IH38: Curing agent H375 = 1 : 1 (by volume) 稀释剂: Thinner: TH90 混合使用时间: Pot-life: 3小时 20 3 hours 漆膜厚度: Indicated film thickness: 干膜: 100-150微米 Dry: 100-150 micron 重涂间隔： Recoat interval: 最小: 8小时 20 Min.: 8 hours 最大
10、: 30 天 20 Max.:30 days 表面处理: Surface preparation: 涂层性能通常于表面处理程度成正比。涂漆前,已涂底漆的表面必须清洁,干燥,无损 伤和污物,包括盐渍。磨圆所有粗糙的焊点并除去焊渣。 Coating performance is proportional to the degree of surface preparation. Prior to coating, primed surface must be clean, dry, undamaged and free of all contaminants, including salt dep
11、osits. Round off all rough welds and remove all weld spatter. 施工方法: Application method: 无空气喷涂, 传统喷涂, 刷涂或滚涂。 Airless spray, conventional spray, brush and roller. 备注备注 Remarks 表面温度必须至少高于露点3以避免水汽凝结。施工时表面不得有冰膜。 Surface temperatures must be at least 3 above dew point to prevent condensation. 安全安全 Precaut
12、ions 本产品在施工时应遵守有关的国家卫生，安全和环境标准及其法规。使用前应获取和咨询有关本产品的材料安全 数据表。注意包装标签上的安全事项。如果你没有完全理解或你不能严格执行这些安全事项，不要使用本产品。 在施工和干燥期间要采取通风措施，维持溶剂蒸汽的容度在安全极限内，防止中毒或缺氧。小心避免与皮肤、眼 睛接触。 All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety and E
13、nvironmental standards and regulations. Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health safety information. Read and follow all precautionary notices on the Material Safety Data Sheet container labels. If you do not fully understand these wa
14、rnings and instructions or if you can not strictly comply with them, do not use this product. Proper ventilation measures must be provided during application and drying to keep solvent vapor concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions
15、to avoid skin and eye contact (i.e. Gloves, goggles, face masks, barrier creams etc.) Actual safety measures are dependant on application methods and work environment. 附注附注 Other Notice 本说明书有关数据是在标准条件下取得，实际使用时，环境条件可能与之略有不同，以上数据如有改变，以本公 司最新说明书为准，恕不另行通知。 All information in this product data sheet is based on standard conditions and slight variation may occur with different conditions. All information in our company is subject to change without notice. 公布日期公布日期 Issued: February 15, 2005
