《开机调试工作内容》由会员分享，可在线阅读，更多相关《开机调试工作内容（5页珍藏版）》请在金锄头文库上搜索。
1、 Test protocol Chilled Water Generation York ( WuXi ) Air Conditioning and Refrigeration Co.,Ltd. bHAcGMP-YK-SAT- 0011 /52018-6-18Section One: Running Procedure 开机程序开机程序开机调试工作内容开机调试工作内容开机调试工作内容开机调试工作内容 CONTENTCONTENTCONTENT OFOFOF RUNNINGRUNNINGRUNNING 一一检查调整检查调整 Inspecting and adjusting A.机组外围检查机组外
2、围检查（下列项目若符合要求，请在“是”前的中打“” ；若不符合要求， 请在“否”前的中打“” ，并在虚线上说明） Inspecting the periphery of the unit (If the following items meet the requirements, please draw“”in at the front of “Yes”; if not, please draw “”in at the front of “No”, and illustrating the reason at the broken line)安装水平是否符合规范： 是(Yes) 否(No)If
3、 the installation level meets the specifications or not:水流开关安装位置是否符合规范： 是 (Yes) 否(No)If the installation location of the flow switch meets the specifications or not冷冻水系统清洗是否符合规范： 是 (Yes) 否(No) If the flushing of the chilled water system meets the specifications or not冷冻水系统放气是否符合规范： 是 (Yes ) 否(No)If
4、the air-exhausting of the chilled water system meets the specifications or not冷冻水泵检查是否符合规范： 是(Yes ) 否(No) If the inspection of the chilled water pump meets the specifications or not冷却水系统清洗是否符合规范： 是(Yes ) 否 (No)If the flushing of the cooling water system meets the specifications or not冷却水系统放气是否符合规范：
5、是(Yes ) 否 (No)If the air-exhausting of the cooling water system meets the specifications or not是否具备冷负荷： 是(Yes ) 否(No) If possessing the refrigeration duty or not是否准备好控制电源： 是(Yes ) 否(No) Test protocol Chilled Water Generation York ( WuXi ) Air Conditioning and Refrigeration Co.,Ltd. bHAcGMP-YK-SAT- 0
6、012 /52018-6-18If making good ready of the controlling power 控制电压：伏特(Volt)Controlling voltage是否准备好各项电源： 是(Yes ) 否(No) If making good ready of all items of power supply是否安装好水流开关： 是(Yes ) 否(No) If well-installing the flow switch or not是否安装好与水泵联锁： 是(Yes ) 否(No) If the interlock with water pump installa
7、tion well or notB.机组阀门检查机组阀门检查 The inspection of the unit valves已检查和开启应开启的阀门 ： Have inspected and turned on all the valves which should be turned on故障阀门及处理： Failure valves check and their disposalC.电机绝缘检查电机绝缘检查 Motor insulation inspecting 用伏绝缘表测量电机绝缘：Use V Insulation testers to measure the motor ins
8、ulation A 相地 Phase-earth兆欧 M, standard is 20MB 相地 Phase-earth兆欧 M, standard is 20MC 相地 Phase-earth 兆欧 M, standard is 20MAB 相 Phase兆欧 M, standard is 20MAC 相 phase兆欧 M, standard is 20MBC 相 phase 兆欧 M, standard is 20M D.联轴器检查联轴器检查（已检查的请在中打“” ，需要时请在虚线上详细说明）The coupling inspecting (If inspected, please d
9、raw“”in the .If necessary, please specify at the broken line)已检查跳动度及锁紧螺丝：Have inspected the runout and locked the screwE.控制线、油泵线、起动柜接线及检查控制线、油泵线、起动柜接线及检查（已检查的请在中打“” ，需要时请在虚 线上详细说明） Controlling line, oil pump line, starting-up cabinet connecting and inspecting (If Test protocol Chilled Water Generati
10、on York ( WuXi ) Air Conditioning and Refrigeration Co.,Ltd. bHAcGMP-YK-SAT- 0013 /52018-6-18inspected, please draw“”in the .If necessary, please specify at the broken line) 接触器检查：Contactor inspecting联锁机构检查：Interlock mechanism inspecting接线及线径要求检查：Wiring and line diameter inspecting所有接线端子检查和紧固：All co
11、nnecting terminal inspecting and tighteningF.控制电源、油泵电源通电检查控制电源、油泵电源通电检查（已检查的请在中打“” ，需要时请在虚线上详 细说明） Controlling power supply, oil pump power supply inspecting while power is on (If inspected, please draw“”in the .If necessary, please specify at the broken line) 检查电压：Inspecting voltage控制中心诊断及设定： Diagn
12、osing and setting for controlling center 电磁阀工作： Check solenoid valve working加热器工作： Check heater working油泵起动及油压： Oil pump starting-up and oil pressure滑阀或导叶校正： Slide valve or vane adjustmentG. 主电源接线及电压检查主电源接线及电压检查 Main power connecting and voltage inspectingA 相电压 phase voltage伏 v B 相电压 phase voltage伏
13、v C 相电压 phase voltage伏 vTest protocol Chilled Water Generation York ( WuXi ) Air Conditioning and Refrigeration Co.,Ltd. bHAcGMP-YK-SAT- 0014 /52018-6-18Test protocol Chilled Water Generation York ( WuXi ) Air Conditioning and Refrigeration Co.,Ltd. bHAcGMP-YK-SAT- 0015 /52018-6-18开机调试开机调试（已检查的请在中打“” ，需要时请在虚线上详细说明）Ru
