《拨动开关SS-12F15规格书技术参数》由会员分享，可在线阅读，更多相关《拨动开关SS-12F15规格书技术参数（4页珍藏版）》请在金锄头文库上搜索。
1、ISSUEDSPECIFICATIONTITLE:SLIDE SWITCH RATING: DC 50V 0.5ACONTACT RESISTANCE:30m ohm MaxMODEL NO:SS-12F-15INSULATION RESISTANNC:100M ohm at 500V DCWITHSTAND VOLTAGE:AC 500V for 1 mintuterUNIT:MMDWNDPERATION FORCE:REFER ATTACH SPECIFICATIONSWITCHING LIFE 10K CYCLES (15-18C/M UNIOADING)SCALE:CHKDBYDRWG
2、 NODATE:2005.5.10东莞市振鑫电子有限公司 VERSION:1文件编号SF-SP-0372东 莞 市 振 鑫 电 有 限 公 司 发布日期2006 年 5 月 29 日SPECIFICATION 规格书第 A 版第 1 页 共 3 页 MODEL NO. 产品名称. 拨动开关DRAWN 制订白春莲APPD. 审批1.RATING (额 定 值) :DC 50V 0.3A2.FUNCTION (接触型式) :1P2T3.TIMING (时间特性) :NOT-SPECIFIED4.ELECTRICAL CHARACTERISTICS (电气性能规格):ITEM 项目TEST COND
3、ITIONS 测试条件PERFORMANCE 规格4.1CONTACT RESISTANCE 接触电阻MEASURED AT 1KHZ SMALL CURRENT(100mA OR LESS) 在 1KHZ微小电流(100 mA 以下)测试.30m MAX. 30 毫欧以下。4.2INSULATION RESISTANCE 绝缘电阻APPLY A VOLTAGE OF 500V DC FOR 1 MIN. TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE. (1) BETWEEN BODY AND TERMINAL. (2)
4、 BETWEEN TERMINALS. 输入 500V DC 电压 1 分钟,按以下接触方法测试; (1) 外壳兴排脚之间. (2) 端子之间.100 M MIN 100 兆欧以上。4.3DIELECTRIC STRENGTH 耐电压AC 500V (50-60HZ)FOR 1 MIN TRIP CURRENT:0.5 mA (1) BETWEEN TERMINALS. (2) BETWEEN TNDIVIDUAL TERMINAL AND FRAME. 输入 AC 500V(50-60 HZ)电压,1 分钟感度电流为 0.5 mA,按以 下接触方法测试: (1) 排脚相互之间 (2) 排脚兴
5、外壳之间WITHOUT DAMAGE TOPARTS ARCINCINC OR BREAKDCMN, ETC. 没有绝缘破坏等异常.5.MECHANICAL CHARACTERISTICS (机械性能规格)ITEM 项目TEST CONDITIONS 测试条件PERFORMANCE 规格5.1OPERATING FORCE 作动力MEASUREMENT SHALL BE MADE AT TRE NEAREST POINT OF THE COMPONENT OR AT THE POINT 3mm FROM THE TIP OF THE ACTUATOR (KNOB). 在距离胶柄前端 3 mm
6、作测定点.300gf100gf5.2TERMINAL BTRENGTH 端子强度A STATIC LOAD OF 300 gf SHALL BE APPLIED TO THE TERMINAL FOR 15 SEC.IN ANY DIRECTION 在排脚前端任意一个方向加 300 gf 力度测试,MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED WITHOUT DAMAGE OR EXCESSIVE LOOSENESS OF ACTUATOR. 在端子中没有裂开、松动等异常, 满足于机械、电器性能5.3DISPLACEM
7、ENT OF ACTUATOR (KNOB) 柄强度A STATIC LOAD OF 10 N(1K gf)SHALL BE APPLIED TO THE TOP OF THE ACTUATOR(KNOB) AND THEN DISPLACEMENT SHALL BE MEASURED TO THE DIR- ECTION OF THE ARROW. 在柄的前端施加 1K gf 的力度,位移应沿印记的方向上定.THE LEVER SHALL HAVE NO SERIOUS DEFORMATION AND FUNCTION IS NORMALLY. 柄部无严重变形,可以正常工作.文件编号SF-S
8、P-0372东 莞 市 振 鑫 电 子 有 限 公 司 发布日期2006 年 5 月 29 日SPECIFICATION 规格书第 A 版第 2 页 共 3 页 6.ENDURANCE CHARACTERISTICS(耐久性):ITEM 项目TIST CONDITIONS 测试条件PERFORMANCE 规格6.1LIFE TEST 寿命试验ENDURANCE WITHOUT LOADING： A SWITCH SHALL BE SUBJECTED TO 10，000 CYCLES AT A SPEED OF 15 TO 18 CYCLES PER MINUTE WITHOUT LOADING
9、. 无负荷: 在无负荷的条件下以每分钟 15-18 回的 速度进行 10,000 次的测试.（1）CONTACT RESISTANCE（接触电阻）100m MAX,100 毫欧以下。 （2）INSULATION RESISTANCE（绝缘电 阻）50M MIN，50 兆欧以上。 （3）WITHSTAND VOLTAGE（耐电压）AC 500V，1 MINUTE.AC 500V 1 分钟 （4）OPERATING FORCE(作动力) 30% INITIAL VALUE. 变化范围初始值30%. （5）WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC
10、.(测试后外表无损伤,并且满足机械性能)6.2SOLDERA- BILITY TEST 可焊性试验THE TOP OF THE TERMINALS SHALL BE DIPPED 2mm IN THE SOLDER BATH OF 2305 FOR 30.5 SECONDS. 端子顶部被浸入锡焊池中 2 mm 深,温度 为 2305, 时间为 30.5 秒。THE AREA OF SOLDERING. SHOULD BE OVER 75%. 焊接面积要有 75%以上.6.3RESISTANCE TO SOLDERING HEAT TEST 耐焊性试验SOLDER BATH METHOD:SOL
11、DER TEMPERATURE 2605 IMMERSION TIME 30.5SEC IMMERSION DEPTH UP TO THE SURFACE OF THE BOARD THICKNESS OF PRINTED WIRING BOARD 1.6 mm DIMENSIONS OFCOMPONENT HOLES IN THE PRINTED WIRING BOARD SHALL SEING ACCORDANCE WITH THOSE SPECIFIED IN THIS SPECIFICATION. 焊炉焊接的时候 时候控制在 2605，过炉时 间 30.5 秒，于（基板）厚度为 1.6
12、 mmWITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED. 本体无变形,能满足于机械、电器性能。6.4COLD TEST 耐冷试验THE SWITCH SHALL BE STORED AT ATEMPERATURE OF -253 FOR 48 HOURS. THEN THE SWITOH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITIONS FOR 1 HOUR AFTER
13、 WHICH MEASUREMENT SHALL BEMADE.-253中 48 小时后,再放置常温 常温中 1 小时来进行测试。THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. 外观无异常,满足于机械、电器性能。东莞市振鑫电子有限公司 http:/文件编号SF-SP-0372东 莞 市 振 鑫 电 子 有 限 公 司发布日期2006 年 5 月 29 日SPECIFICATION 规格书第 A 版第 3 页 共 3 页6.5HEAT TEST 耐热试验THE SWITCH SHALL BE STORED AT ATEMPERATU
14、RE O 702 FOR 48 HOURS. THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE. 放置在温度 702中测试 48 小时后,再放置正常室 温中 1 小时来测定.6.6HUMIDITY TEST 潮湿试验THE SWITCH SHALL BE STORED AT ATEMPERATUREOF 402 AND A HUMIDITY OF 90% TO 95% FOR 96 HOURS.THEN T
15、HE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE. 放置 402的相对温度为 90%95%环境中 96 小时 后,再将样版放在正常环境 1 小时后进行测试.THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. 外观无异常,满足于机械、电器 性能。6.7STANDARD ATMOSPHERIC CONDITIONS 测试标准状态UNLELL OTHERWISE SP
16、ECIFIED. THE STANDARD RANGE OF ATMOSPHERIC CONDITIONS FOR MAKING MEASUREMENTS AND TESTS ARE AS FOLLOWS: （1）AMBIENT TEMPERATURE : 5 TO 35 （2）RELATIVE HUMIDITY :45% TO 85% （3）AIR PRESSURE :86kpa TO 106kpa 在没有指定的情况下测试温度、湿度、气压如下: （1）温度为 535. （2）湿度为 45% TO 85%. （3）气压为 86kpa TO 106kpa.6.8PRACTICAL TEMPERATURE RANGE 使用温度范围-16+60. 在-16
