《常用改模具英汉对照》由会员分享，可在线阅读，更多相关《常用改模具英汉对照（4页珍藏版）》请在金锄头文库上搜索。
1、常用改模具英汉对照常用改模具英汉对照模具常用語英航对照1. 紅色區域要咬花(拋光).The red area should be textured(polished).2. 紅色區域要作 1 度拔模角.The red area should be 1 degree draft angle.3. 紅色區域要減(加)膠 0.05mm.The red area should be reduced(added)0.05mm.4. 修改前Before modifying5. 修改後After modifying6. 修改 Modify 7. 此位做頂針The location of ejector is
2、 here.8. 此位做扁頂針The location of ejector blade is here.9. 此位做司筒The location of ejector sleeve is here.10.此位做斜頂The location of lifter is here.11.此位做滑塊The location of slide is here.12.此位要做入子The location of insert is here.13.此線條表示 PLThis line is PL.14.涂色區域會產生縮水The coloured area will be shrinkadge.15.此處會有
3、毛邊There will be flash here.16.此處尖角建議改成 0.5R 角The sharp angle is suggested to change to 0.5R angle.17.此處膠位太薄不易入膠This material is too thin to shot.18.此處膠位太厚會縮水This material is too thick so as to be shrinkadge.19.此段差為 0.05mmThe mismatch is 0.05mm.20.此處易產生段差(此處會有段差)Here is easy to be mismatch.21.建議用放電花替
4、代咬花紋Suggest to spark erosion instead of texture.22.此位要拋光Here should be polished.23.此位要增加 0.05 度拔模角度Here should be added 0.05 degree draft.24.一次灌點的位置The location of the first gate.25.此位不能有水口殘留Here cant be residual gate.26.水口殘留最大 0.1mm.The maximal residual gate is 0.1mm.27.此水口會用 CNC 銑平The gate will be
5、 milled to flat by CNC.28.此位會作凹陷Here will be recess.29.此位會做凸出Here will be bluge.30.此處設置火山口A crater is will be here.31.此位會做平或是下沉 0.05mmHere will be flat or recess 0.05mm.32.此位會有斜頂痕Here will be lifer markings.33.此處會有線痕.Here will be line markings.34.此位一次減膠,讓二次膠延伸下來Here the first material is to be cut t
6、o let the second material to flow .35.此位一二次封膠困難,二次會溢料Here the first and second material is difficult to envelop and the second will overflow.36.分析此位無拔模,建議作一度By analysis,here is no draft and suggest to be one degree.37.頂針位置如圖,穴號刻在頂針上The location of ejector is shown as in the picture and the cavity nu
7、mber is graved on ejector.38.滑塊拆在肋位中間Slide should be part in the middle of rib.39.公模仁拔模修改到一度The draft of core is modified to one degree.40.此位是擋膠用(圖示中的位置是為擋膠)It is used to slow down the moldflow.41.此位會產生結合線Splite line will outcome here.42.此位會有包風There will be airtrap here.43.此膠位先填充頂部Moldflow will fill
8、 in the top first.44.此位有倒扣Its undercut here.45.此處要做枕位It is should be shut-off here.46.此位模具強度不夠The tooling is lack of strength.47.建議取消此處圓角It suggests to cancle the rad angle.48.二次進膠點作搭接The second gate should be 49.公母模靠破(碰穿)The cavity and core mold shut off.50.此位間隙太小The gap here is too narrow.51.此柱位容易粘模This boss is easy to stick mold.52.在此骨位上作扁頂針Ejector blade is on the rib.53.此骨位太深,建議加大拔模角The rib is too deep so it suggests to enlarge the draft.54.此位要作排氣孔Here should be an air-vent hole.
