《单片机为核心的温度控制系统毕业论文》由会员分享,可在线阅读,更多相关《单片机为核心的温度控制系统毕业论文(51页珍藏版)》请在金锄头文库上搜索。
1、沈阳航空工业学院北方科技学院毕业设计(论文)I摘摘 要要本文介绍了一种以单片机为核心的温度控制系统,它集信号采集,温度显示和温度控制于一体。由于其在工业方面的大量应用,研究它工程价值极高,文中详细叙述了它的发展史和在工业领域的应用。之后,提出方案,分章介绍它的硬件和软件设计方法与思想。其中软件中的温度控制为整个程序的灵魂,它的控制思想是利用模拟信号转换成数字信号进入单片机 89C51,显示温度控制。根据温差的大小,输出不同的控制信号,达到控制温度的目的。硬件方面采用 8155 与 LED和键盘连接的成熟技术完成显示和设定值输入。最后通过软硬联调,检验系统功能。关键词:关键词:单片机;LED 显
2、示;A/D 转换器 沈阳航空工业学院北方科技学院毕业设计(论文)IIAbstractOne kind of the temperature centering on monolithic machine the main body of a book has been introduced controls system , it incorporates the signal collect , temperature display and the temperature under the control of into an integral whole. Since whose gr
3、eat quantity in the field of industry applies, study its project value extremely highly , has narrated its phylogeny and the application in industry field detailedly in culture. Afterwards, suggest that the scheme , mark of seal introduce its hardware and the software design procedures with thought.
4、 The temperature under the control of in softwares among them is entire procedure soul, its 89 C51 controlling thought being that the digital signal making use of an analog signal to change Cheng enters the monolithic machine , display temperatures under the control of. According to the size of diff
5、erence in temperature, export the different pilot signal , achieve under the control of the temperatures purpose. Hardware aspect adopt 8155 and the mature technology that LED and the keyboard link accomplishes display and setting value importing. Allocate , check system function finally by couplet
6、gentle or harsh.Keywords: Monolithic machine; LED is demonstrated; A/D converter沈阳航空工业学院北方科技学院毕业设计(论文)III目目 录录1 绪 论11.1 概述11.2 课题研究的工程价值和应用 32 系统硬件设计42.1 任务分析及硬件原理图42.2 单片机概述52.2.1 信号滤波电路的设计72.3 A/D 转换器 ADC080982.3.1 ADC0809 引脚 82.3.2 ADC0809 结构及转换原理 92.3.3 MCS-51 与 ADC0809 的接口102.4 单片机 89C51 及外围接口电路112.4.1 复位电路的设计132.4.2 时钟电路的设计142.5 8155H 扩展 I/O 口完成键盘/显示功能152.5.1 8155H 的引脚和功能152.5.2 8155H 的命令字162.5.3 LED 电路介绍182.5.4 键盘接口原理202.6 控制执行电路的设计213 系统软件设计223.1 主程序说明233.2 系统初始化模块的设计233.3 数据采集子程序253.4 数据处理子程序26沈阳航空工业学院北方科技学院毕业设计(论文)IV3.5 键盘扫描程序273.6 显示程序设计294 系统调试314.1 软件调试324.2 联通调试方案