《年产63万吨热轧线材车间设计_安徽工业大学》由会员分享，可在线阅读，更多相关《年产63万吨热轧线材车间设计_安徽工业大学（85页珍藏版）》请在金锄头文库上搜索。
1、安徽工业大学工商学院 毕业设计（论文）说明书共 2 页 第 1 页 装 订 线 关键词是为了文献标引工作从论文中选取出来用以表示全文主题内容信息款目的 词或术语。如有可能，应尽量用 汉语主题词表等词表提供的规范词。 不用此 信息时，删除此框 。毕业设计论文说明书年产 63 万吨热轧线材车间设计摘 要根据毕业设计的要求，设计年产63 万吨的热轧高速线材生产车间， 采用单线轧制方式。产品规格为5.516mm，单卷盘重约2 吨。本设计产品包括碳素结构钢和优质碳素钢。本车间设计的内容主要有：产品大纲和金属平衡表的制定；设计工艺方案和工艺流程；工作制度的确定及轧机生产能力分析；主要设备的选择；辅助设备的
2、选择及计算；车间平面布置及起重运输；车间 技术经济指标；环境保护；孔型设计；轧机力能参数计算及电机设备校核等。本设计原料采用连铸坯，以减少金属的 损失，而且连铸坯的组织结构较好，这也提高了产品的质量；还可以减少轧制间隙时间 ，提高生产率。加热炉为步进梁式加热炉，进出料方式采用侧进侧出，以保证炉子的严密性 ，加热能力为120t/h。加热炉由微机控制，出炉温度为10501250C。轧机采用高速线材轧机，全线均为无扭轧制 ，终轧保证速度为100 m/s，最高轧制速度为120m/s。为改善产品微观组织，轧后采用控制冷却技术，轧后冷却通过水冷箱和一套斯太尔摩冷却运输系统来完成。斯太尔摩冷却运输系统采用延
3、迟型冷却运输装置，它适用于冷却各类碳钢，具有较好的冷却效果。总之，上述先进工艺技术和设备是本设计的产品高质量的重要保证；同时也为高线生产车间设计提供了一个很好的样板。关键词：车间设计 高速线材 线材轧机 控制轧制安徽工业大学工商学院 毕业设计（论文）说明书共 2 页 第 2 页 装 订 线 A workshop of new hot rolled high-speed wire with the output of 630,000 t/aAbstractAccording to the requirements of graduation design, a new single line o
4、f high-speed wire rod workshop with the output of 630,000 t / a will be built. Product specifications are for 5.516 mm diameter, each coil weighs about 2 tons. The products in this design include the carbon structural steel and high-quality carbon steel. The main contents of the design are mainly as
5、 follows, formulation of products scheme and metal balance, design of technological plan and process, the determination of work routine and production capacity analysis of rolling mill, choice of the main equipment, choice and calculation of the auxiliary equipment, the grooves design, the layout of
6、 workshop and hoisting and conveying equipment, check of roll strength and motor power, technical and economic indicators of the workshop and environmental protection etc. The continuous casting billet is used as raw materials in this design to reduce the metal loss. The better microstructure of the
7、 billets can also improve the quality of the product and reduce the rolling gap time to increase productivity. The reheating furnace is a walking beam type furnace which is side entry and side exit to ensure the tightness of the furnace. The heating capacity is 120t / h. The furnace is controlled by
8、 the computer. The exit temperature is 10501250C. The high-speed wire rod mill is used in this workshop. No twist rolling is realized across the rolling line. The finishing ensure speed is 100 m / s, maximum rolling speed of 120m / s. The controlled cooling technology is used after rolling through t
9、he cooling water box and a Stelmor cooling conveyor system to improve product microstructure. Stelmor transportation system by the delayed cooling type cooling transport devices, which applies to various carbon steels and has better cooling effect. In short, the advanced technology and equipment, th
10、e design of the product is an important guarantee of high quality and providing a good model for the high speed wire production workshop designing.Key Words: workshop design high-speed wire rod and wire mill controlled rolling安徽工业大学工商学院 毕业设计（论文）说明书共 4 页 第 1 页 装 订 线 目 录引 言.11 产品方案和金属平衡.41.1 车间产品大纲.41.2 产品质量执行标准及产品交货条件 .41.2.1 执行标准.41.2.2 交货条件.41.3 原料.51.3.1 原料来源和年需要量.51.3.2 钢坯尺寸和质量要求.51.3.3 连铸坯的化学成分.51.4 金属平衡表.52 设计方案.72.1 轧机数量的确定.72.2 轧机布置方案.83 工艺流程.
