《清除和关闭静态映射》由会员分享，可在线阅读，更多相关《清除和关闭静态映射（4页珍藏版）》请在金锄头文库上搜索。
1、R0(config)# R0(config)# R0(config)#int s1/0 R0(config-if)# R0(config-if)# R0(config-if)#no fram R0(config-if)#no frame-relay inv R0(config-if)#no frame-relay inverse-arp R0(config-if)# R0(config-if)# R0(config-if)# R0(config-if)#exit R0(config)#exit R0#cle R0#clear f *Mar 1 03:59:34.491: %SYS-5-CONF
2、IG_I: Configured from console by consoleram R0#clear frame-relay i R0#clear frame-relay inarp R0# R0# R0#sh fram R0#sh frame-relay map R0#sh frame-relay map Serial1/0 (up): ip 172.16.134.1 dlci 103(0x67,0x1870), static,CISCO, status defined, active Serial1/0 (up): ip 172.16.134.5 dlci 104(0x68,0x188
3、0), static,broadcast,CISCO, status defined, active Serial1/0 (up): ip 172.16.134.3 dlci 104(0x68,0x1880), static,CISCO, status defined, active R0#conf t Enter configuration commands, one per line. End with CNTL/Z. R0(config)#int s1/0 R0(config-if)# R0(config-if)# R0(config-if)# R0(config-if)# R0(con
4、fig-if)# R0(config-if)# R0(config-if)# R0(config-if)# R0(config-if)#do sh run int s1/0 Building configuration.Current configuration : 266 bytes ! interface Serial1/0ip address 172.16.134.1 255.255.255.0encapsulation frame-relayserial restart-delay 0frame-relay map ip 172.16.134.5 104 broadcastframe-
5、relay map ip 172.16.134.1 103frame-relay map ip 172.16.134.3 104no frame-relay inverse-arp endR0(config-if)#no frame-relay map ip 172.16.134.5 104 broadcast R0(config-if)#no frame-relay map ip 172.16.134.1 103 R0(config-if)#no frame-relay map ip 172.16.134.3 104 R0(config-if)#exit R0(config)#exit R0
6、#sh *Mar 1 04:00:18.071: %SYS-5-CONFIG_I: Configured from console by consolefram R0#sh frame-relay map R0#sh frame-relay map R0#sh fram R0#sh frame-relay map R0#sh frame-relay map R0#ping 172.16.134.1Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 172.16.134.1, timeout is 2 seconds:
7、 . Success rate is 0 percent (0/5) R0#conf t Enter configuration commands, one per line. End with CNTL/Z. R0(config)#frm R0(config)#fram R0(config)#frame-relay ma R0(config)#frame-relay map R0(config)#int s1/0 R0(config-if)#fram R0(config-if)#frame-relay map R0(config-if)#frame-relay map ip 172.16.1
8、34.1 103 R0(config-if)#exit R0(config)#exitR0# *Mar 1 04:01:55.098: %SYS-5-CONFIG_I: Configured from console by consoleping R0#ping R0#ping 172.16.134.1Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 172.16.134.1, timeout is 2 seconds: ! Success rate is 100 percent (5/5), round-trip
9、 min/avg/max = 80/134/220 ms R0# R0# R0# R0#conf t Enter configuration commands, one per line. End with CNTL/Z. R0(config)#int s1/0 R0(config-if)# R0(config-if)# R0(config-if)#fram R0(config-if)#frame-relay map R0(config-if)#frame-relay map ip 172.16.134.2 103 br R0(config-if)#frame-relay map ip 172
10、.16.134.2 103 br R0(config-if)#frame-relay map ip 172.16.134.2 103 R0(config-if)#exit R0(config)#exit R0#sh fram R0#sh frame-relay m *Mar 1 04:03:25.770: %SYS-5-CONFIG_I: Configured from console by consoleap R0#sh frame-relay map Serial1/0 (up): ip 172.16.134.2 dlci 103(0x67,0x1870), static,CISCO, s
11、tatus defined, active Serial1/0 (up): ip 172.16.134.1 dlci 103(0x67,0x1870), static,CISCO, status defined, active R0#conf t Enter configuration commands, one per line. End with CNTL/Z. R0(config)#int s1/0 R0(config-if)#fram R0(config-if)#frame-relay map R0(config-if)#frame-relay map ip 172.16.134.3
12、104 R0(config-if)#exit R0(config)# R0(config)#exit R0#sh fram R0#sh frame-relay *Mar 1 04:03:53.138: %SYS-5-CONFIG_I: Configured from console by consolemapR0#sh frame-relay map Serial1/0 (up): ip 172.16.134.2 dlci 103(0x67,0x1870), static,CISCO, status defined, active Serial1/0 (up): ip 172.16.134.1 dlci 103(0x67,0x1870), static,CISCO, status defined, active Serial1/0 (up): ip 172.16.134.3 dlci 104(0x68,0x1880), static,CISCO, status defined, active R0#
