《a3000n㊣官方密级拆机文档》由会员分享，可在线阅读，更多相关《a3000n㊣官方密级拆机文档（30页珍藏版）》请在金锄头文库上搜索。
1、D I S A S S E M B L Y P R O C E D U R E 3 - 1 3 - 1 Chapter 3 Disassembly Procedure Please follow the information provided in this section to perform the complete disassembly procedure of the notebook. Be sure to use proper tools described before. SUS A3000N Series Notebook consists of various modul
2、es. This chapter describes the procedures for the complete notebook disassembly. In addition, in between procedures, the detailed disassembly procedure of individual modules will be provided for your service needs. The disassembly procedure consists of the following steps: Battery module HDD Module
3、Memory Module Wireless LAN Module CPU Module ODD-Module Keyboard LCD Module Top Case Module Motherboard Module Bottom Case Module A D I S A S S E M B L Y P R O C E D U R E 3 - 2 3 - 2 Battery module The illustration below shows how to remove the battery module. Removing Battery Module 1. Turn over t
4、he notebook. 2. Slide the battery latch (No.1) to unlock. 3. Firmly slide the other latch (No.2) to the top and remove the battery. B A T T E R Y 1 2 B A T T E R Y M O D U L E R E M O V A L D I S A S S E M B L Y P R O C E D U R E 3 - 3 3 - 3 HDD Module The illustrations below show how to remove the
5、HDD module from the notebook. Removing HDD Module 1. Release 1 screw (No.1) M2*4L, (K) B-NI, NY from the HDD cover. 2. Lift the HDD cover away. 3. Pull out the hard drive and lift the hard drive away by 2 hands. H D D M O D U L E R E M O V A L H D D M O D U L E 1 D I S A S S E M B L Y P R O C E D U
6、R E 3 - 4 3 - 4 Disassembling HDD Module Remove 2 screws here (No.2, No.3) M3 * 3L (K) B-NI and 2 screws (No.4, No.5) M3 * 3 L (K) B-NI on the other side to separate HDD from HDD housing. *Please do not touch inside of the HDD module. H D D M O D U L E D I S A S S E M B L Y4 4 5 3 2 D I S A S S E M
7、B L Y P R O C E D U R E 3 - 5 3 - 5 Memory Module The A3000N Series Notebook comes standard with one SO-DIMM in SO-DIMM socket. There is another expansion SO-DIMM socket for you to upgrade the total memory up to 1024MB with two 512MB SO-DIMM. Removing Memory module 1. Remove 2 screws on DDR Door (No
8、.1, No.2) M2*3L(K, D3.4) W-NI NY 2. Lift the DDR Door away 3. Open the 2 latches aside (No. 3, 4), which will pop the memory module up to an angle of 30, then pull out the memory module in that angle (No. 5). M E M O R Y M O D U L E M E M O R Y R E M O V A L 1 2 5 4 3 30o D I S A S S E M B L Y P R O
9、 C E D U R E 3 - 6 3 - 6 Wireless LAN Module The illustration below shows how to remove the Wireless LAN module. Removing Wireless LAN module 1. Remove 2 Antenna cables from Wireless LAN Module. (No.1, No.2) (White cable: AUX, Black cable: MAIN) 2. Remove the Wireless LAN module by opening the 2 lat
10、ches aside, which will pop the module up to an angle of 30, then pull out the module in that angle just like memory module. W I R E L E S S L A N 2 1 30o W I R E L E S S L A N R E M O V A L D I S A S S E M B L Y P R O C E D U R E 3 - 7 3 - 7 CPU Module The illustrations below show how to remove the
11、CPU module from the notebook. Removing CPU 1. Remove 2 screws on the Thermal Door, (No.1, No.2) M2*4L, (K) B-NI, NY. 2. Lift the Thermal Door away. C P U R E M O V A L C P U 2 1 D I S A S S E M B L Y P R O C E D U R E 3 - 8 3 - 8 3. Disconnect the cable on CPU module. 4. Remove the 2 screws aside th
12、e CPU fan (No.3, No.4) M2 * 6L (K, D4.6) (K) B- NI, NY. 5. Lift the CPU FAN module away. 3 4 D I S A S S E M B L Y P R O C E D U R E 3 - 9 3 - 9 6. Remove the 4 screws upon the CPU module (No.5 No.8) M2 * 6L (K, D4.6) (K) B-NI, NY. 7. Take away the CPU heat sink module gently. 6 8 5 7 D I S A S S E
13、M B L Y P R O C E D U R E 3 - 103 - 10 8. Turn the non-removable screw here 180 degrees counter-clockwise to loosen the CPU. 9. Squeeze the vacuum handling pump and use it to lift the CPU away. * Dont touch the die above the CPU. Unlock L OD I S A S S E M B L Y P R O C E D U R E 3 - 113 - 11 ODD Mod
14、ule The illustration below shows how to remove the ODD module. 1. Remove 2 screws from the cover (No.1, No.2) M2 * 4L (K) B-NI, NY. 2. Put the screwdriver (No. 3) here and push the ODD drive out from the NB. O D D M O D U L E 1 2 3 O D D R E M O V A L D I S A S S E M B L Y P R O C E D U R E 3 - 123
15、- 12 3. Remove 4 screws (no.4-7) M2 * 2L (P) W-NI from ODD bracket. 4 5 7 6 D I S A S S E M B L Y P R O C E D U R E 3 - 133 - 13 Keyboard The illustration below shows how to remove the keyboard Removing Keyboard 1. Remove 2 screws here (No.1, No.2) M2 * 6L (K, D4.6) (K) B-NI, NY 2. Turn over the NB
16、and open the display panel. 3. Push the 3 latches in (No.1, No.2, No.3) with a pair of tweezers or a single- slotted screwdriver and lift the keyboard plate up. K E Y B O A R D R E M O V A L K E Y B O A R D D I S A S S E M B L Y 1 2 1 2 3 D I S A S S E M B L Y P R O C E D U R E 3 - 143 - 14 4. Lay the keyboard down over the Touch Pa
