《夜光brinyte专业潜水手电筒div02说明书》由会员分享，可在线阅读，更多相关《夜光brinyte专业潜水手电筒div02说明书（5页珍藏版）》请在金锄头文库上搜索。
1、夜光 Brinyte 专业潜水手电筒 DIV02 说明书 产品说明：本款夜光 Brinyte 潜水手电筒采用美国最新 CREE XM-L2 LED,最高亮度达 550lumen, 使用 3节 AA 电池, 高亮续航时间可达 2 小时.头部旋转开关，操作简单，60 米的潜水深度，12 度的发光角度, 筒身设计符合人体工程学，是您潜水照明的首选伴侣。 This handheld dive light utilize the USA CREE XM-L2 LED, max 550lumens output, powered by 3*AA dry battery, 2 hours runtime i
2、n high output.Twist on/off switch at head, very easy for you to operate, rated to the depth underwater 60 meters and 12 degree beam angle. The crust is designed according to the ergonomic human engineering. Absolutely it is the first company for the underwater adventure. 产品参数：ANSI 高亮档 中亮档 低亮档 爆闪档 SO
3、S 档亮度 550 流明 / / / /续航时间 2 小时 / / / /最大光强 10800 坎德拉最大射程 300 米防跌落测试 1.5 米防水等级 IP68 水下 60 米注：以上参数是在实验室环境中测试所得，可能会随着手电的使用环境和电池不同而发生变化。Technical Parameters:ANSI High Medium Low Strobe SOSOutput 550lumen / / / /Runtime 2 Hours / / / /Intensity 10800cdDistance 300mDrop Resistant 1.5mWaterproof IP68 underw
4、ater 60mThe parameters above have been tested under laboratory conditions, so they may vary between different batteries and environments. 产品规格：-采用美国进口 CREE XM-L2 U2 LED 灯珠，寿命超过 50000 小时；-可以使用 3 节 AA 电池；-电流稳定，亮度恒定；-过热保护，防止外壳温度过高影响使用；-防反接保护，防止因电池反装而损害手电；-尾盖（凸台）大挂绳孔设计，可以悬挂快扣；-旋转头部或者筒身即可开关手电，操作方便；-三层防水圈
5、设计，使潜水深度达到 60 米；-航空铝材+ABS 材质；-采用军工三级硬质阳极氧化抗磨和抗腐蚀处理，经久耐用-采用镀膜防刮花钢化玻璃；-光学分析设计的铝合金反光杯；-产品大小：39 mm (头)*33 mm (中)*33 mm (尾)*204 mm (长 ) * 240g（净重）-配件：O 圈，润滑油，手绳，说明书；-其他可选配件：礼盒，手腕带.Product Specification:-Cree XM-L2(U2) LED, lifespan is over 50,000 hours;-Uses 3*AA batteries.-High efficiency constant curre
6、nt circuit, constant brightness-Over-heat protection, preventing the high temperature from influencing the normal use;- Reverse polarity protection to protect from improper battery installation;-Super big lanyard hole design for bolt snap mount; -Twist on/off switch, easy to operate; -Three O- rings
7、 design to ensure underwater 60 meters;-Aircraft-grade aluminum and ABS material;-Premium type III military hard-anodized finish for abrasion and corrosion resistance.-Toughened glass can stand higher water pressure resistance- Alloy aluminum reflector-Dimensions: 39(Head dia.)*33(Body dia.)*33(Tail
8、 dia.)*204(L)mm*240g(Net weight)-Standard accessories: 3 spare O-rings, Lubricant, lanyard, user manual-Other accessories (optional): gift box, wrist strap. 产品分解图及说明：Products structure and instruction; 操作说明：a) 电池安装电池正极对准灯头方向(如图)，旋紧头部即可使用b) 开关电源拧紧头部和筒身可以开关电筒，拧松就可以关闭；Operation:a) Battery installationb
9、) Keep the battery positive pole direction same as the light head(as shown in the picture), tighten the head to turn on the light.c) Tighten the head to turn on the light, unscrew the head to turn off the light. 注意事项：1）所有潜水电筒的连接处（除开关部位）在出货前都会密封，用户请不要擅自打开；2）为了避免进水的可能，我们建议潜水前就打开电筒（开关一定拧紧）；3）避免水下多次拧动；4
10、）手电长时间不用，需将电池取出，否则可能因电池漏液或者爆炸造成手电损害。Note:1) All of the connections (except the switch) are sealed before shipment, PLEASE dont disassemble it by you self.2) For avoiding the possibility of the dive light floored underwater, we suggest to turn on the light before diving. 3) Dont twist the switch many
11、 times underwater4) Please take the batteries out of the light if you dont use it for long time, or the light may be damaged by the battery leakage or detonation. 手电保养：1）每次潜水后请及时用淡水浸泡电筒；2）每次使用之后开关部分建议擦润滑油；3）请勿将电筒放在沙地上，以防细沙进入开关和螺纹缝隙；4）请经常检查 O 圈，如有损害请及时更换，以维持手电的防水性能；5）请经常清洁手电的导电接触面以保证手电的正常工作。Flashligh
12、t maintenance:1） Please immerse the dive flashlight in the fresh water for few minutes after diving and clean the water after immersing;2） Please put lubricant on the switch threads after diving3） Please dont drop or place your dive flashlight in sand, in case the sand go into the switch and threads
13、4） Please inspect the O-rings often, change a new one once there is any damage.5） Please clean the conductive connections often to ensure the flashlight work normally. 手电常见问题自我检测：当手电出现异常闪烁或者无法工作的时候，以用以下方法来自我检测：1) 电池电量不足-需要更换电池；2) 螺纹或者 PCB 板的导电接触面被弄脏-请用酒精清理接触面如果上述方法无效，请联系经销商并按照售后服务条款接受保修。FAQ and Dete
14、ction:When the flashlight flash unusually or cant turn on, it might be the reasons below1) The battery voltage is too low-please replace new batteries2) The threads, PCB board contact other contacts are dirty-Clean the contact points with an alcohol soaked cotton swab.If the methods above dont work, please contact the distributors and refer to the warranty policy 友情提示：本手电亮度很高，请勿照射肉眼或者直视光源，以免视力损伤，特别是儿童。Friendly tips:Please DO NOT shining the light directly into the eyes, in case damage the eyesight, especially for children. 保修条款（和保修卡放在一起）Warranty policy:
