《基于plc的c616车床控制系统设计》由会员分享,可在线阅读,更多相关《基于plc的c616车床控制系统设计(23页珍藏版)》请在金锄头文库上搜索。
1、哈 尔 滨 理 工 大 学 学 士 学 位 论 文- 1 -大 学毕 业 设 计题 目 : 基 于 PLC 的 C616 车 床 控 制 系 统 设 计 院 、 系 : 姓 名 : 指 导 教 师 : 系 主 任 : 年 月 日哈 尔 滨 理 工 大 学 学 士 学 位 论 文- 2 -摘 要车 床 是 机 械 加 工 中 使 用 最 广 泛 的 机 床 , 它 可 以 用 于 切 削 各 种 工 件 的 外 圆 、 内 孔 、 端面 及 螺 纹 等 。 现 代 生 产 机 械 多 采 用 机 械 、 电 气 、 液 压 、 气 动 相 结 合 的 控 制 技 术 。 电 气 控制 技 术 起
2、 联 接 中 枢 作 用 , 应 用 最 为 广 泛 。 用 普 通 机 床 加 工 出 来 的 产 品 普 遍 存 在 质 量 差 、品 种 少 、 档 次 低 、 成 本 高 、 供 货 期 长 , 所 以 本 次 设 计 以 普 通 车 床 为 对 象 , 设 计 了 一 套综 合 、 高 效 的 PLC 控 制 系 统 , 提 高 普 通 车 床 的 生 产 效 率 、 控 制 精 度 和 产 品 质 量 。PLC( 可 编 程 控 制 器 ) 作 为 一 种 工 业 控 制 微 型 计 算 机 , 它 以 其 编 程 方 便 、 操 作 简单 尤 其 是 它 的 高 可 控 性 等
3、优 点 , 在 工 业 生 产 过 程 中 得 到 了 广 泛 的 应 用 。 本 次 设计 就 是 以 PLC 控 制 系 统 取 代 传 统 的 继 电 器 -接 触 器 控 制 系 统 。文 章 首 先 介 绍 了 普 通 车 床 的 结 构 以 及 电 气 控 制 系 统 , 然 后 介 绍 了 PLC 控 制 系 统 的硬 件 结 构 、 工 作 原 理 以 及 设 计 PLC 控 制 系 统 的 基 本 原 则 和 步 骤 , 根 据 任 务 要 求 设 计 了PLC 控 制 系 统 , 其 中 包 括 PLC 的 选 型 、 硬 件 设 计 以 及 软 件 设 计 等 。 最 后
4、 连 接 西 门 子 触摸 屏 KTP1000 装 置 , 实 现 监 控 和 控 制 操 作 。本 设 计 的 关 键 就 是 要 在 原 继 电 器 控 制 电 路 的 基 础 上 , 经 过 合 理 的 转 换 , 从 而 设 计出 具 有 相 同 功 能 的 PLC 控 制 程 序 。全 套 图 纸 , 加哈 尔 滨 理 工 大 学 学 士 学 位 论 文- 3 -AbstractMachining lathe is the most widely used tool, it can be used to cut various parts of the cylindrical, bo
5、re, thread end, and so on. The modern production machinery uses the control technology which the machinery, the electricity, the hydraulic pressure, air operated unify. The electric control technology plays the joint main center role, the application is most widespread. Out of the ordinary machining
6、 prevalence of poor quality products, variety of small, low grade, high cost, delivery and long, so this design object is an ordinary lathe, designed a comprehensive and efficient PLC control system, improved lathe productivity, control accuracy and product quality. PLC (programmable controller) as
7、an industrial control micro-computer, with its easy programming, simple operation, especially its high controllability, etc., in the industrial production process has been widely used. The PLC control system design is to replace traditional Relay - contact device control system.The article first int
8、roduces the lathe, and electrical control systems, PLC control system and then introduces the hardware structure, operation principle and design of the basic principles of PLC control systems and procedures, according to the task to design a PLC control system, including the PLC elections type, hard
9、ware design and software design. Finally, Siemens touch screen TP177B connected devices, monitoring and control operations to achieve.The key originally designed is that should be on the basis of control circuit of original relay, through rational conversion , thus design PLC control procedure with
10、same function.哈 尔 滨 理 工 大 学 学 士 学 位 论 文- 4 -目 录摘 要 .2Abstract .3目 录 .4引 言 .61 C616 型 普 通 车 床 概 述 .71.1 C616 型 车 床 的 主 要 结 构 .71.1.1 C616 车 床 的 主 要 运 动 .71.2 C616 型 普 通 车 床 技 术 参 数 表 .72 车 床 电 气 控 制 系 统 分 析 及 总 体 设 计 .82.1 车 床 的 电 气 控 制 电 路 原 理 图 .82.2 车 床 电 路 分 析 和 电 气 控 制 要 求 .92.2.1 主 电 路 分 析 .92.2.2 控 制 电 路 分 析 .92.2.3 信 号 及 照 明 电 路 .102.3 电 器 元 件 明 细 表 .102.4 电 气 控 制 系 统 总 体 设 计 思 路 .113 系 统 硬 件 设 计 及 PLC 概 况 和 应 用 .