《高细风选粉碎机使用指南》由会员分享，可在线阅读，更多相关《高细风选粉碎机使用指南（13页珍藏版）》请在金锄头文库上搜索。
1、 高细风选粉碎机 http:/ 余种非易燃、易爆物料进行粉碎加工。粉碎物料硬度一般不大于莫氏硬度 7 级，湿度根据物料特性而定，一般不超过 3-10%，成品细度 30-325 目。二、主要技术参数 高细风选粉碎机 http:/ Any Change of technical data will not inform additionally.三、结构及工作原理本机主要由主机、风机、分离器、集粉器、除尘器等型 号技术参数400 型 700 型最大进料粒度（毫米）30 30成品粒度（目）30-325 30-325产量（公斤/小时）100-800 200-2500主轴转速（转/分）2900 2300
2、外型尺寸（米）4.624.3 122.54.5设备重量（吨）1.5 3主机电机（千瓦）Y160L-2-18.5 Y200L-2-37风机电机（千瓦）Y112M-2-4 Y132S-2-7.5 高细风选粉碎机 http:/ 3 毫米。2.细调： 高细风选粉碎机 http:/ ）调节风帽高低：在分离器内，芯管上端装有可升降风帽，风帽降低，细度升高，反之细度相应下降。风帽由风帽支架支撑在芯管上，如果您要求的细度较低可去掉风帽试调。（2 ）风量调节：在引风机进风立管下部装有翻板调节器进行风量调节，风量小细度高，风量大细度低，但应注意风量过小时容易从分离器回料咀向外喷料，请用户适当调整。（3 ）主机风扇
3、叶调整：如果风量已调到最小，风帽降到最低，细度仍达不到要求，这时可将主机风扇叶减少，减少为 3 片或者 2 片，使主机送风量减小，增加物料在机内粉碎时间。3.通过以上调整，细度达到要求，即可连续生产，如果更换物料，改变细度，应再行调整。五、安装安装可参考基础图以及结构示意图（附后），用户可以根据厂房情况适当调整布局。六、使用及保养1.主机和风机轴承每周加洁净黄油一次。2.开机前须转动主轴，检查机内有无异常声音，发现问题及时处理，以免损坏机件。3.进料要求均匀，粒度可根据原料硬度适当调整，较硬 高细风选粉碎机 http:/ 3 厘米以下较为理想。4.严禁将金属块投入机内，以免打坏机件。5.400
4、 型布袋长度不少于 2.5 米，700 型布袋长度不少于 3 米。使用中应经常抖动，使粉尘落入料仓，便于排风。6.开关机顺序：开机时，先开风机，后开主机；停机时，先停主机，后停风机。七、易损件明细表注：技术数据如有变动，恕不另行通知。机 型 名 称数 量（件）材 质打 板 6高锰钢（ZGMn13 ）400衬 板 7耐磨铸铁（ HT200）打 板 6高锰钢（ZGMn13 ）700衬 圈 2高锰钢（ZGMn13 ） 高细风选粉碎机 http:/ Fine Air Separation PulverizerGXF-400 & GXF-700Operational Manual 高细风选粉碎机 htt
5、p:/ Great Wall Heavy Industry Machinery Co., Ltd.Add: Crossroad of JIANGSHAN Road and KAIYUAN Road towards West, Huiji District, Zhengzhou City, China.Post Code: 450044Tel:0086-371-63769782 Fax:0086-371-63769781CategoryI. Usage & ApplicationII. Main SpecificationIII. Construction & Working Principle
6、IV.Output Adjustment 高细风选粉碎机 http:/ InstallationVI.Operation & MaintenanceVII. Wearing PartsI. Usage and ApplicationHigh Fine Air Separation Pulverizer is widely applying in various industries such as mining, construction materials, chemical industry, medicine, feedstuff etc. It can be used to have
7、a comminuting process to several hundreds of non-flammable & non-explosive materials with Moths Hardness are below 7 and humidity is no more than 10%. The output size can be adjusted from 30 to 525 meshes. 高细风选粉碎机 http:/ Main Specification Specification GXF400 GXF700 Feeding Size (mm) 30 30Final pro
8、ducts (Mesh) 30-525 30-525 Capacity (kgs/h) 100-800 200-2500Main Shift Speed（r/m）2900 2300 Overall Dimension (m) 4.6*2*4.3 12*2.5*4.5 Weight (ton) 1.5 3.0 Motor power(KW) Y160L-2-18.5 Y200L-2-37 高细风选粉碎机 http:/ power(KW) Y112M-2-4 Y1322S-2-7.5 III. Construction & Working PrincipleThis pulverizer is c
9、onstituted with main machine, air blower, separator, powder collector, air filter and other parts; the main machine consists of crushing chamber, blocking chamber and fan chamber.When material is evenly fed into a crushing chamber, the main shaft rotates in high speed. The material will be comminute
10、d with the aid of impact of main shaft cutter blade and casing interior lining panel and the shorn of high pressure airflow, after that, the material comminuted will via a chamber enter into a separator for re-grading treatment, the coarse material will return to the crushing chamber via a return no
11、zzle for re-pulverization, while the finished material will enter into a powder collector via a draught fan for bagging and packing purpose, the rest airflow will be exhausted via a device which is used for dedust and exhaust.IV.Output Adjustment 高细风选粉碎机 http:/ General AdjustmentLoose the screw bolt
12、s of blocking frame in the machine and regulate the gap between blocking panel and cone-shaped panel to get needful outlet size. Regulate the gap smaller to get fine outlet size and regulate it bigger to get coarse outlet size. Whatever, you should keep the gap no smaller than 3mm.2. Precise Adjustment1) Adjust hood height: The hood at the top of core pipe in the separator can be lifted up-and-down. Lower the hood to get fine outlet size and in other way to get coarse size. If you want to get finer outlet size, please try to remove the hood.2) Air Volume ControlAir volu
