《hub-spoke帧中续配置》由会员分享，可在线阅读，更多相关《hub-spoke帧中续配置（5页珍藏版）》请在金锄头文库上搜索。
1、Configuring Hub and Spoke Frame Relay拓朴:实验步聚：1. 使用 Frame Relay配置 配置R1配置!hostname R1!interface Serial3/0ip address 192.168.0.1 255.255.255.0encapsulation frame-relayserial restart-delay 0 frame-relay map ip 192.168.0.2 102 broadcastframe-relay map ip 192.168.0.3 103 broadcastno frame-relay inverse-ar
2、p! R2配置!hostname R2!interface Serial3/0ip address 192.168.0.2 255.255.255.0encapsulation frame-relayserial restart-delay 0frame-relay map ip 192.168.0.1 201 broadcastframe-relay map ip 192.168.0.3 203 broadcastno frame-relay inverse-arp! R3配置!hostname R3!interface Serial3/0ip address 192.168.0.3 255
3、.255.255.0encapsulation frame-relayserial restart-delay 0frame-relay map ip 192.168.0.1 301 broadcastframe-relay map ip 192.168.0.2 302 broadcastno frame-relay inverse-arp! 调试R2上进行调试R2#show frame mapSerial3/0 (up): ip 192.168.0.1 dlci 201(0xC9,0x3090), static,broadcast,CISCO, status defined, activeS
4、erial3/0 (up): ip 192.168.0.3 dlci 201(0xC9,0x3090), static,broadcast,CISCO, status defined, activeR2#show frame pvcPVC Statistics for interface Serial3/0 (Frame Relay DTE)Active Inactive Deleted StaticLocal 2 0 0 0Switched 0 0 0 0Unused 2 0 0 0DLCI = 201, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, IN
5、TERFACE = Serial3/0input pkts 7 output pkts 6 in bytes 588 out bytes 554 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 1 out bcast bytes 34 5 minute input rate 0 bits/sec
6、, 0 packets/sec5 minute output rate 0 bits/sec, 0 packets/secpvc create time 00:11:34, last time pvc status changed 00:10:34DLCI = 203, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial3/0input pkts 6 output pkts 6 in bytes 554 out bytes 554 dropped pkts 0 in pkts dropped 0 out pkts droppe
7、d 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 1 out bcast bytes 34 5 minute input rate 0 bits/sec, 0 packets/sec5 minute output rate 0 bits/sec, 0 packets/secpvc create time 00:11:35, last time pvc status changed 00:10
8、:35DLCI = 204, DLCI USAGE = UNUSED, PVC STATUS = ACTIVE, INTERFACE = Serial3/0input pkts 0 output pkts 1 in bytes 0 out bytes 34 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast
9、pkts 1 out bcast bytes 34 5 minute input rate 0 bits/sec, 0 packets/sec5 minute output rate 0 bits/sec, 0 packets/secpvc create time 00:11:35, last time pvc status changed 00:10:35DLCI = 205, DLCI USAGE = UNUSED, PVC STATUS = ACTIVE, INTERFACE = Serial3/0input pkts 0 output pkts 1 in bytes 0 out byt
10、es 34 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 1 out bcast bytes 34 5 minute input rate 0 bits/sec, 0 packets/sec5 minute output rate 0 bits/sec, 0 packets/secpvc cr
11、eate time 00:11:36, last time pvc status changed 00:10:36R2#ping 192.168.0.1Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 192.168.0.1, timeout is 2 seconds:!Success rate is 100 percent (5/5), round-trip min/avg/max = 32/82/112 msR2#ping 192.168.0.3Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 192.168.0.3, timeout is 2 seconds:!Success rate is 100 percent (5/5), round-trip min/avg/max = 16/100/292 msR2#参考文档
