《cisco交换机vtp配置》由会员分享，可在线阅读，更多相关《cisco交换机vtp配置（8页珍藏版）》请在金锄头文库上搜索。
1、Cisco 交换机 vtp 配置实验环境：cisco Packet Tracer5.3拓扑图：1. Ds 的配置Switch#conf tEnter configuration commands, one per line. End with CNTL/Z.Switch(config)#hostname Ds1Ds1(config)#vtp domain jvtcChanging VTP domain name from NULL to jvtcSwitch(config)#vtp mode serverDs1(config)#interface gigabitEthernet 0/1Ds1(
2、config-if)#switchport mode accessDs1(config-if)#switchport mode trunk%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to down%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to upDs1(config-if)#exitDs1#show vtp status VTP Version : 2C
3、onfiguration Revision : 0Maximum VLANs supported locally : 1005Number of existing VLANs : 5VTP Operating Mode : ServerVTP Domain Name : jvtcVTP Pruning Mode : DisabledVTP V2 Mode : DisabledVTP Traps Generation : DisabledMD5 digest : 0x97 0x15 0xF7 0x52 0x62 0x24 0x0B 0xEC Configuration last modified
4、 by 0.0.0.0 at 0-0-00 00:00:00Local updater ID is 0.0.0.0 (no valid interface found)Ds1#copy running-config startup-config Destination filename startup-config? Building configuration.OKDs1#2. As1 的配置SwitchenSwitch#conf tEnter configuration commands, one per line. End with CNTL/Z.Switch(config)#hostn
5、ame As1As1(config)#interface gigabitEthernet 1/1As1(config-if)#switchport mode trunkAs1(config-if)#exitAs1(config)#interface gigabitEthernet 1/2As1(config-if)#switchport mode trunkAs1(config-if)#exitAs1(config)#vtp domain jvtcDomain name already set to jvtc.As1(config)#vtp mode clientSetting device
6、to VTP CLIENT mode.As1(config)#exitAs1#show vtp statusVTP Version : 2Configuration Revision : 0Maximum VLANs supported locally : 255Number of existing VLANs : 5VTP Operating Mode : ClientVTP Domain Name : jvtcVTP Pruning Mode : DisabledVTP V2 Mode : DisabledVTP Traps Generation : DisabledMD5 digest
7、: 0x97 0x15 0xF7 0x52 0x62 0x24 0x0B 0xEC Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00As1#copy running-config startup-config Destination filename startup-config? Building configuration.OKAs1#3. As2 的配置SwitchenSwitch#conf tEnter configuration commands, one per line. End with CNTL/Z.Switc
8、h(config)#hostname As1As1(config)#interface gigabitEthernet 1/1As1(config-if)#switchport mode trunkAs1(config-if)#exitAs1(config)#vtp domain jvtcDomain name already set to jvtc.As1(config)#vtp mode clientSetting device to VTP CLIENT mode.As1(config)#exitAs1#show vtp statusVTP Version : 2Configuratio
9、n Revision : 0Maximum VLANs supported locally : 255Number of existing VLANs : 5VTP Operating Mode : ClientVTP Domain Name : jvtcVTP Pruning Mode : DisabledVTP V2 Mode : DisabledVTP Traps Generation : DisabledMD5 digest : 0x97 0x15 0xF7 0x52 0x62 0x24 0x0B 0xEC Configuration last modified by 0.0.0.0
10、at 0-0-00 00:00:00As2#copy running-config startup-config Destination filename startup-config? Building configuration.OKAs2#4.vlan 中继查看Ds1#vlan database% Warning: It is recommended to configure VLAN from config mode,as VLAN database mode is being deprecated. Please consult userdocumentation for confi
11、guring VTP/VLAN in config mode.Ds1(vlan)#vlan 10VLAN 10 added:Name: VLAN0010Ds1(vlan)#vlan 20VLAN 20 added:Name: VLAN0020Ds1(vlan)#vlan 30VLAN 30 added:Name: VLAN0030Ds1(vlan)#vlan 40VLAN 40 added:Name: VLAN0040Ds1(vlan)#exitAPPLY completed.Exiting.As1#show vtp status VTP Version : 2Configuration Re
12、vision : 4Maximum VLANs supported locally : 255Number of existing VLANs : 9VTP Operating Mode : ClientVTP Domain Name : jvtcVTP Pruning Mode : DisabledVTP V2 Mode : DisabledVTP Traps Generation : DisabledMD5 digest : 0x4A 0xDC 0x4A 0x49 0x15 0xD9 0x91 0xF7 Configuration last modified by 0.0.0.0 at 3
13、-1-93 00:42:47#As2#show vtp status VTP Version : 2Configuration Revision : 4Maximum VLANs supported locally : 255Number of existing VLANs : 9VTP Operating Mode : ClientVTP Domain Name : jvtcVTP Pruning Mode : DisabledVTP V2 Mode : DisabledVTP Traps Generation : DisabledMD5 digest : 0x4A 0xDC 0x4A 0x49 0x15 0xD9 0x91 0xF7 Configuration last modified by 0.0.0.0 at 3-1-93 00:42:47As2#
