《smtc 5 330 001-2010(v1) 座椅及饰件织物面料(最终稿)》由会员分享，可在线阅读，更多相关《smtc 5 330 001-2010(v1) 座椅及饰件织物面料(最终稿)（14页珍藏版）》请在金锄头文库上搜索。
1、SMTC 5 330 0012010（V1）I上汽股份有限公司技术中心企业技术标准Enterprise Technical Standard of SAIC Motor Technical CenterSMTCSMTC 5 330 0012010（V1 ）2010-XX-XX 发布/Issue 2010-XX-XX 实施/Implementation上 汽 股 份 技 术 中 心 技 术 标 准 化 委 员 会 T ech n ica l S ta n d a rd iza tio n C o m m ittee o f S A IC M o to r T ech n ica l C en t
2、er 发布Issue座椅及饰件织物技术要求Seat and Trim Finisher Fabric Technical RequirementSMTC 5 330 0012010（V1）I目 次/Contents前言 Foreword.II1 范围 Scope .12 规范性引用文件 Normative references .13 一般要求 General requirement.13.1工作 条件 Service Conditions .13.2材料认可 Material Approval .23.3标准样板 Master Samples .23.4运输和储存 Transit and S
3、torage .33.5生产线试验 Production Trial .34 其它要求 Other requirement.45 织物类型 Types of Fabric.46 织物结构 Fabric Construction.47 试验 Testing.47.1试验要求及方法 Test requirement and method .47.2试验条件 Test condition .58 试验说明 Notes on test.78.1 平方米克重 Weight.88.2 纬斜 Skewed weft and bowed weft.88.3耐污及耐清洁 Soiling and cleaning
4、 .88.4 汗渍色牢度溶液 Perspiration solution.9附录 A Appendix A.10SMTC 5 330 0012010（V1） II前 言为规范 SMTC座椅及饰件织物面料技术要求及试验方法，特制定此标准。当中英文产生疑义时，以中文为准。本标准的附录 A 为资料性目录，附录 B 为规范性附录。本标准由基础分标委提出。本标准由 SMTC技术标准化委员会批准。本标准由标准化工作组归口管理。本标准起草部门：内外饰部、质保部。本标准主要起草人：陈刚、蔡明、赵天瑜、金学哲。本标准于 2010年 XX月 XX日首次批准发布，2010年 XX月 XX日实施。ForewordTh
5、is standard is established for regulating SMTC seat and trim finisher fabric technical requirement and test method. This standard is written in Chinese and English but if in doubt, the Chinese version should be criterion.Annex A is normative reference. This standard was proposed by basic sub-committ
6、ee.This standard was approved by the SMTC Technical Standardization Committee.This standard was specification management by Standardization working team.The drafting departments of this standard are: Exterior and Interior Dept，QA Dept.The main drafters of this standard are: Chen Gang、Cai Ming、 Zhao
7、Tianyu、Jin Xuezhe.This standard was first published on XX. XX,2010 and implemented on XX. XX, 2010.SMTC 5 330 0012010（V1）1座椅及饰件织物技术要求 Seat and Trim Finisher Fabric Technical Requirement1 范围本标准包含了对座椅及饰件织物面料的性能的要求和试验方法。饰件包含门饰板、立柱饰板、顶饰及其他可能用到织物的车内内饰零件。在本标准中并没有对织物的结构进行指定说明。符合本标准的织物包括：机织物，经编织物，纬编织物。1 Sco
8、pe This Standard covers the general performance requirements and test method for seat and trim finisher fabrics. The trim finisher should include the door casing, pillar, headliner and any interior components which might use the fabric. Fabric constructions are not specified in this document. Fabric
9、s covered by these requirements include Woven, Warp knitted, Weft knitted.2 规范性引用文件下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注日期的引用文件，其随后所有的修改单（不包括勘误的内容）或修订版均不适用于本标准，然而，鼓励根据本标准达成协议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件，其最新版本适用于本标准。2 Normative referencesThe following normative documents contain provision which, through r
10、eference in this text, constitute provisions of this standard. For dated reference, subsequent amendments to, or revisions of, any of these publications do not apply (exclude the correction), but parties to agreements based on this standard are encouraged to investigate the possibility of applying t
11、he most recent editions of the standards. For undated references, the latest edition of the normative document referred to applies.MGR ES.30.CR.130 内饰材料耐汗液色牢度 MGR ES.30.CR.130 Color Fastness to Perspiration of Trim MaterialsMGR ES.30.CR.426 装饰织物的水渍评估 MGR ES.30.CR.426 Water Marking Assessment of Trim
12、 FabricsMGR ES.30.DS.103薄片状塑料材料和纺织品的尺寸稳定性MGR ES.30.DS.103Dimensional stability of sheet form plastic materials and textilesMGR ES.30.DS.736纺织物的湿收缩 MGR ES.30.DS.736 Wet Shrinkage of TextileMGR ES 30.TF.101接缝疲劳和滑移 MGR ES 30.TF.101 Seam Fatigue and SlippageMGR ES.30.TP.102纺织材料的断裂负荷和至断拉伸长度MGR ES.30.TP.102 Breaking Load and Elongation of Break of Textile Materials thickness of textiles and textile productsMGR ES.30.TR.425梯形撕裂强度 MGR ES.30.TR.425 Trapezoid Tearing StrengthSMTC 08502 供应商零件的首次供货和变更供货的批准程
