《微机控制外文翻译》由会员分享，可在线阅读，更多相关《微机控制外文翻译（7页珍藏版）》请在金锄头文库上搜索。
1、外文资料SYSTEM OVERVIEWThe DTS is a lost cost,computer controlled test system which is capable of testing a wide range of linear IC,s.The system is contained in a single cabinet and has a relatively small footprint.The major components of the DTS are:Motorola Micorosystems VME series computerSmall profi
2、le printerInstrumentataion card cagePower supply traysHewlett Packard 3456A or 3458DVM1.Motorola Microsystems ComputersThe VME/10 is a MC68010 based microcomputer built around the VMEbus architecture.The testers software runs under the VERSAdos operating system and the RMS68K real-time multitasking
3、kernel. The computer has 384K bytes of main memory ,a memory management unit,a real-time clock/calendar, and 5 slot VMEbus card cage.Also include are a double-side ,double-density floppy disk drive and a 40Mb hard disk.Added in the card cage are a GPIB controller board,a dual parallel board,a 512Kb
4、memory expansion board,and an instrumention bus controller.The VMEsystem 1131 is a MC68020 based machine designed around a twelve slot VMEbus compatible cardcage. The system unit,16Kb of instruction cache,2Mb of ram ,and a mass storage unit that houses a 70Mb hard disk, 655Kb floppy disk,and a 60Mb
5、streaming tape drive.Added to this are a GPIB controller hard and an IBUS controller board and an IBUS controller board. The terminal used as the system console is a Motorola TM3000 terminal.On both computer systems, the tester software runs under the VERSAdos operating system and the RMS68K real-ti
6、me multitasking kernel.The DTS environment is designed to look and operate the same on both systems.2 Printer The printers is a small,Centronics compatible dot matrix printer.Its dimensions allow it to reside on an extendable shelf within the DTS cabinet.It is connected to the VME/10 through one of
7、the available parallel ports,or to the SYS1131 via one of the serial ports.3 Instrumentation Card RackMost of the tester instrumentation is installed in the upper portion of the DTS cabinet . The card rack can hold up to sixteen test instrument cards:DC measurement system boardTest head matrix board
8、Voltage source and nanoammeter boardAudio voltmeter boardControl and measure bits boardTime measurement boardHandler or prober control board Audio source boardEight voltage and current source boardsThe card rack also contains an analog and a digital backplane for controlling each module.The digital
9、backplane is connected to the computer via the IBUS cabling.The power V/I source is a special instrument that ,when installed in the system ,is mounted inside the back door as opposed to being in the card rack.3.1 The measurement boardCard slot one contains the measurement board.The measurement boar
10、d is a differential DC voltmeter with a maximum input voltage of +65V to -65V.The measurement board has three measurement ranges,65V,20V,and 2V.3.2 The cross point matrix boardCard slot two holds the cross point matrix board.The cross matrix board consists of three sections:a timer interval generato
11、r,a sixteen input measurement matrix,The time interval generator is used to time and control program waits in the DTS system.The measurement matrix is input matrix for the measurement board.It provides sixteen that can be used to connect the measurement board to different measurement points on the l
12、oad board.3.3 The voltage source/nanoammeters(vs/na) boardProvides eight individually programmable voltage sources capable of forcing voltages from -65V DC to +65V DC at currents up to 10mA.Voltage sources one through four also have built in current measurement capability.The VS/NA board is located
13、in card slot three of the instrument card rack.。The VS/NA board has two voltage forcing ranges.65V DS and 10V DC.and has two current measurentment ranges,a 20uA range ang a 2uA range.3.4 The audio voltmeter(AVM) boardCard solt four holds the audio voltmeter board,which provides the capability of mea
14、suring AC signals in the audio frequency range.The AVM board provides DC suppression and filtering of the input signal,and has an input frequence range of 50HZ and 100KHZ.The AVM has six voltmeter ranges:16,4,1.6,0.4,0.1,and 0.025V RMS,and the following user selectable filters:Highpass:50HZ,300HZ,an
15、d 3KHZBandpass:None,1KHZ,10KHZ,19KHZ,38KHZ,and Distortion3.5 The CBITS/MBITS boardCard solt five contains the CBITS/MBITS board,which provides 32 control lines to the performance board,and 16 read-back bits(MBITS) form the performance board.3.6 The large timer boardThe large timer board is located i
16、n card slot six,and is used to measure the elapsed time between two events,or to count the number of events which occurred during a known time interval.3.7 The handler control board The handler control board provides the interface between the DTS and the device handler or prober.It receives a start test signal from the handler when a decice is sitting in the handlers contacts and is ready for testing.After testing has been completed,the handler control board provides a
