《硬齿面圆柱齿轮减速器说明书》由会员分享，可在线阅读，更多相关《硬齿面圆柱齿轮减速器说明书（6页珍藏版）》请在金锄头文库上搜索。
1、硬齿面圆柱齿轮减速器CYLINDER GEAR REDUCER 使用说明书SERVICE MANUALXXXXXXXXXXXXXXXXXXXX REDUCER CO., LTD.概述.Overview硬齿面圆柱齿轮减速器广泛应用于运输、冶金、矿山、化工、轻工等各种机械设备的传动机构中。其工作条件应符合下列要求：Cylinder gear reducers are widely used for individual mechanical equipment in the fields such as transportation,metallurgy,mining,chemical indus
2、try and light industry etc. Suitable scope of reducers:1、高速轴转速不大于 1500r/min；Rotation Speed of high-speed shaft not exceed 1500r/min；2、工作环境温度为-20+45；当环境温度低于 0时，启动前润滑油应加热到 010；Working environment temperature ranges from -20+45; If it is under 0 , the lubricating oil must be preheated until the tempera
3、ture is 010；3、齿轮圆周速度不大于 20m/s。Gear circumferential speed not exceed 20m/s。.标记：.Remark： 轴端型式装配型式公称传动比名义中心距型号 Shaft and TypeAssembling TypeNominal Transmission RatioNominal Central DistanceType.安装、使用及维护.Installation、Operation and Maintenance1、安装：减速器的输入轴线和输出轴线与其连接的原动机和负载轴线，应保证同轴，其误差不得大于所用联轴器的允许值，优先选用弹性
4、联轴器，有利于提高减速器的使用寿命。安装联轴器时不许锤击。Installation：The input axis and output axis of the reducer shall be coaxial with the connected driver axis and load axis. The clearance shall not exceed the allowed value for the used coupling, with the elastic coupling axis preferentially selected, thus helping to exten
5、d reducer operation duration. And the hammering is not allowed in the installation of the coupling axis.2、加油：减速器安装好后，向箱体内加足所需润滑油，油面应达到规定高度。Add oil：After completing reducer installation, add enough lubricating oil into the oil tank until the oil level up to the stipulated level.3、润滑油的选用：环境温度-100时用 L-
6、CKC4668 润滑油；030时用 L-CKC100150 润滑油；30以上时用 L-CKC220 润滑油；Lubricating oil selection：Select to use L-CKC4668 lubricating oil for the environment tempetature ranging from -100，L-CKC100150 lubricating oil for the environment temperature ranging from 030,and L-CKC220 lubricating oil for the environment temp
7、erature over 30.4、换油：减速器首次使用一个月后必须更换润滑油，且热机换油，并冲洗干净，第二次需三个月更换一次，以后每六个月换油一次，同时定期检查油的质量，发现混入杂质或老化变质需随时更换，油位低于规定高度时需及时补足。Oil Changes：One month later after reducer first putting into operation, the lubricating oil shall be ON-LINE changed in operation and be flushed for cleaning. Three months later chan
8、ged the lubricating oil again. After that lubricating oil shall be changed every six months. And meanwhile the oil quality shall be inspected periodically. Change the lubricating oil at any moment if any impurity or deterioration, and supply the lubrication oil if oil level is lower than stipulated
9、level.5、油温异常现象：在使用中当发现油温显著升高，温升超过 60或油池温度超过 80及产生不正常的噪音等现象时，应停止使用，查明原因，排除故障。如因齿面胶合所致，必须修复，更换新油后再使用。Oil Temperature Abnormal etc：If the oil temperature increase dramatically in operation , or the increment temperature exceed 60, or oil tank temperature exceed 80, or the abnormal noise exists, stop th
10、e operation of the reducer and perform the trouble-shooting. If failure is caused by gear agglutination, repair the gear and change new oil before re-start.6、渗油处理：使用中发现结合面渗油，请拆开渗漏处零件涂 601密封胶，或发现油封漏油，请按原型号更换。 Oil Leaking：If the bonding surface is leaking, please remove the components at the leaking p
11、oint and coat with 601 sealant. If the oil seal is found, please change with the original type.7、贮存时间：减速器出厂前，已将机内润滑油放尽，因此贮存期不能超过半年，以免生锈。Storage Time：The lubrication oil had been drained out in the factory before delivery. The storage period shall not exceed half a year to avoid the rust.8、有限责任：减速器未经
12、商议，用户自行解体或改造而出现的问题，本厂不负任何责任。Limited Liability： The plant is not responsible for the problems caused by the users disassembling or changing the reducer without prior consultation.轴承、油封型号. Type of Bearing and Ring部 件规 格 PartSize高速轴部件Hight Speed Shaft Parts第一中间轴部件First Midshaft Parts第二中间轴部件Second Midsh
13、aft Parts第三中间轴部件Third Midshaft Parts低速轴部件Low Speed Shaft Parts轴承Bearing3231785x180x63.52 只32324120x260x90.52 只32332160x340x1212 只32248240x440x1272 只23072C360x540x1342 只油封Rubber Ring85x110x122 只 360x400x202 只油泵Pump BB-B25 or BB-B32吸油、滤油器Oil-Sucking FilterTF-40x80合 格 证CERTIFICATE产品名称 Name规格型号 Type产品编号
14、 No.检 验 员 Inspector发证日期 Date本产品经检验合格，准予出厂。The reducer has been passed through the strict inspection in accordance with the standards and codes for manufacturing, assemblingas well as performance, and approved to be delivered.厂址：XXXXXXXXXXthe Site of Factory：XXXXXXXXXX邮编：XXXXXX 传真：XXXXXXXXXXXPostalcode：XXXXXX Fax：XXXXXXXXXXX服务热线：XXXXXXXXXXXService Phone：XXXXXXXXXXXhttp：/ XXXXXXXXXXXE-mail： XXXXXXXXXXX
