《rx8640创建npar分区实例》由会员分享,可在线阅读,更多相关《rx8640创建npar分区实例(4页珍藏版)》请在金锄头文库上搜索。
1、RX8640 创建 npar 分区实例一、试验环境:(1 ) 设备型号:RX8640(2 ) 系统版本:HPUX 11.31 IA(3 ) 可用资源:两个 CELL 板,Cell0 、Cell1二、实验过程:1、 cmRR重启 CELL 到 BIB 状态下2、 cmCC创建第一个分区3、 cmRS4、查看#parstatus #parstatus V p0查看分区 0 状态#parstatus AC 查看可用的空闲 CELL 板5、 #parcreate c 1:-B P 1 创建以 CELL1 为 core cell 的分区 1,下图为命令执行及成功的回显:#parstatus 查看分区 1
2、 是否曾创建成功:CPU Memory UseOK/ (GB) Core OnHardware Actual Deconf/ OK/ Cell Next ParLocation Usage Max Deconf Connected To Capable Boot Num= = = = = = = =cab0,cell0 Active Core 4/0/8 16.0/0.0 cab0,bay0,chassis0 yes yes 0 cab0,cell1 Inactive 4/0/8 16.0/0.0 cab0,bay0,chassis1 yes yes 16、现在分区 1 是处于非激活状态,Cm
3、RS重启分区 17、重启后发现没有系统盘8、进入分区 0,删除分区 1#parremove p 1只能删除非激活的分区,但此时分区 1 为激活状态,下图为失败报错:#ParstatusCPU Memory UseOK/ (GB) Core OnHardware Actual Deconf/ OK/ Cell Next ParLocation Usage Max Deconf Connected To Capable Boot Num= = = = = = = =cab0,cell0 Active Core 4/0/8 16.0/0.0 cab0,bay0,chassis0 yes yes 0
4、cab0,cell1 Active Core 4/0/8 16.0/0.0 cab0,bay0,chassis1 yes yes 1 9、所以需要 cmRR 分区 1,然后执行 parremove#parstatusCellCPU Memory UseOK/ (GB) Core OnHardware Actual Deconf/ OK/ Cell Next ParLocation Usage Max Deconf Connected To Capable Boot Num= = = = = = = =cab0,cell0 Active Core 4/0/8 16.0/0.0 cab0,bay0
5、,chassis0 yes yes 0 cab0,cell1 Inactive 4/0/8 16.0/0.0 cab0,bay0,chassis1 yes yes 1#parremove p 1删除分区 1CellCPU Memory Use OK/ (GB) Core OnHardware Actual Deconf/ OK/ Cell Next ParLocation Usage Max Deconf Connected To Capable Boot Num= = = = = = = =cab0,cell0 Active Core 4/0/8 16.0/0.0 cab0,bay0,cha
6、ssis0 yes yes 0 cab0,cell1 Inactive 4/0/8 16.0/0.0 cab0,bay0,chassis1 yes - -12、 #parmodify p 0 a 1:将 CELL1 加入分区 0根据操作提示 #shutdown R重启后进入系统查看:#parstatus V p0查看分区 0 信息CellCPU Memory UseOK/ (GB) Core OnHardware Actual Deconf/ OK/ Cell Next ParLocation Usage Max Deconf Connected To Capable Boot Num= = = = = = = =cab0,cell0 Active Core 4/0/8 16.0/0.0 cab0,bay0,chassis0 yes yes 0 cab0,cell1 Active Base 4/0/8 16.0/0.0 cab0,bay0,chassis1 yes yes 0