《Checklist Annex I Machinery Directive》由会员分享，可在线阅读，更多相关《Checklist Annex I Machinery Directive（16页珍藏版）》请在金锄头文库上搜索。
1、1Checklist Compliance Essential Health and Safety RequirementsGiven below are the relevant requirements of the Machinery Directive. More particularly, these are the requirements recited in ANNEX I “Fundamental health and safety requirements concerning the design of machines and safety components.” A
2、 copy of the Machinery Directive is an essential aid in the interpretation of the summary report below.The obligations imposed in the fundamental health and safety requirements are only applicable if the relevant danger is present in the machine in question when the machine is used in the manner int
3、ended by the manufacturer. That is to say, the manufacturer need only consider the intended use, and the reasonably foreseeable misuse of his machinery, but need not consider unreasonable misuse.The requirements stated in the directive are compulsory. Given the state of technology it is possible tha
4、t the set objectives cannot be reached. In such cases, the manufacturer has an obligation, through design and construction modification, to come as close to meeting the objective as technology permits.Each requirement is checked as to whether the machinery meets the requirement or whether the requir
5、ement is not applicable.All users information must be in the language of the county of the user. Where applicable a mark is used to indicate that instructions in the language of the end-user are to be provided.Date:Machine Name: Project Number: Checklist performed by: Page:2Machinery Directive Requi
6、rement(paragraph number and title)Comply Remarks1.1. General remarks1.1.2. Principles of safety integration1.1.3. Materials and products1.1.4. Lighting1.1.5. Design of machinery to facilitate its handling1.2. Controls1.2.1. Safety and reliability of control systems1.2.2. Control devices1.2.3. Starti
7、ng1.2.4. Stopping1.2.5. Mode selectionDate:Machine Name: Project Number: Hazard Identification performed by: Page:3Machinery Directive Requirement(paragraph number and title)Comply Remarks1.2.6. Failure of the power supply Conforms to the Low Voltage Directive and to EN 60204-11.2.7. Failure of the
8、control circuit Conforms to the Low Voltage Directive and to EN-60204-11.2.8. Software1.3Protection against mechanical hazards1.3.1. Stability1.3.2. Risk of break-up during operation1.3.3. Risks due to falling or ejected objects1.3.4. Risks due to surfaces, edges or angles1.3.5. Risks related to com
9、bined machinery1.3.6. Risks relating to variations in the Date:Machine Name: Project Number: Hazard Identification performed by: Page:4Machinery Directive Requirement(paragraph number and title)Comply Remarksrotational speed of tools1.3.7. Prevention of risks related to moving parts1.3.8. Choice of
10、protection against risks related to moving parts1.4. Required characteristics of guards and protection devices1.4.1. General requirement1.4.2. Special requirements for guards1.4.2.1. Fixed guards1.4.2.2. Movable guards1.4.2.3. Adjustable guards restricting access1.4.3. Special requirements for prote
11、ction devices1.5. Protection against other hazards1.5.1. Electricity supply Conforms to the Low Voltage Directive and to EN-60204-1Date:Machine Name: Project Number: Hazard Identification performed by: Page:5Machinery Directive Requirement(paragraph number and title)Comply Remarks1.5.2. Static elect
12、ricity Conforms to the Low Voltage Directive and to EN-60204-11.5.3. Energy supply other than electricity1.5.4. Errors of fitting1.5.5. Extreme temperatures1.5.6. Fire1.5.7. Explosion1.5.8. Noise Conduct sound measurement and take appropriate measures as necessary, e.g. reduce noise level, prescribe
13、 personal protection equipment such as adequate ear protection.1.5.9. VibrationDate:Machine Name: Project Number: Hazard Identification performed by: Page:6Machinery Directive Requirement(paragraph number and title)Comply Remarks1.5.10. Radiation Applies only to apparatus that produces or contains i
14、onizing radiation.1.5.11. External radiation Conforms to the EMC Directive 89/336/EEC (see EMC analysis below)1.5.12. Laser equipment1.5.13. Emissions of dust, gases, etc.1.5.14. Risk of being trapped in machine1.5.15. Risk of slipping, tripping or falling1.6. Maintenance1.6.1. Machinery maintenance
15、 All set-up and maintenance functions can be safely performed, following the provided instructions and common practices such as lock-out from power supplies.Date:Machine Name: Project Number: Hazard Identification performed by: Page:7Machinery Directive Requirement(paragraph number and title)Comply
16、Remarks1.6.2. Access to operating position and servicing points1.6.3. Isolation of energy sources Conforms to the Low Voltage Directive and to EN-60204-1, as well as isolation ability for other sources of energy (compressed air, chemical supplies, etc.)1.6.4. Operator intervention1.6.5. Cleaning of internal parts1.7. Indicators1.7.0. Information devices The indicators provided for use in ordinary operation are:1.7.1. Warning devices The warning devices pro
