《托辊线取料装置设计_毕业设计》由会员分享,可在线阅读,更多相关《托辊线取料装置设计_毕业设计(32页珍藏版)》请在金锄头文库上搜索。
1、 密级: 托辊线取料装置设计Design of feeding roller device I摘 要随 着 现 代 经 济 的 飞 速 发 展 , 重 工 业 也 在 快 速 的 发 展 , 因 此 输 送 装 置 的 运 用 就 越来 越 普 遍 了 , 输 送 装 置 主 要 是 采 用 输 送 带 , 而 输 送 带 行 业 正 朝 着 节 能 、 节 材 、 安 全 、环 保 型 发 展 。 由 钢 绳 、 尼 龙 、 涤 纶 、 芳 纶 为 骨 架 材 料 的 输 送 带 将 快 速 发 展 , 更 注 重提 高 抗 冲 击 、 防 撕 裂 、 耐 磨 耗 、 耐 臭 氧 等 性 能
2、 和 使 用 寿 命 ; 具 有 各 种 用 途 的 阻 燃 输送 带 、 环 保 型 密 闭 式 输 送 带 、 轻 型 输 送 带 、 大 倾 角 输 送 带 、 高 强 力 提 升 带 、 耐 热 、耐 油 、 耐 酸 碱 、 耐 热 输 送 带 以 及 各 种 花 纹 输 送 带 等 功 能 性 和 特 殊 需 求 的 高 强 力 输 送带 将 迅 速 发 展 , 逐 渐 形 成 输 送 带 的 重 要 产 品 。 与 此 同 时 , 发 展 循 环 经 济 也 成 为 输 送带 行 业 发 展 的 另 一 个 新 的 课 题在 输 送 装 置 高 速 发 展 的 大 好 形 势 下
3、, 作 为 输 送 装 置 的 一 种 取 料 装 置 , 也 正 在 突飞 猛 进 的 发 展 , 取 料 装 置 是 一 种 非 标 准 件 , 用 于 工 厂 的 某 些 特 殊 的 场 合 , 适 用 的 范围 很 单 一 , 一 般 都 是 工 厂 大 量 长 期 执 行 某 个 动 作 而 设 计 的 , 而 我 设 计 的 这 个 托 辊 线取 料 装 置 主 要 实 现 三 个 动 作 , 回 转 、 上 升 、 翻 转 。 通 过 这 几 个 动 作 把 托 辊 从 钢 丝 绳上 取 下 来 , 这 三 个 动 作 都 是 用 液 压 缸 来 完 成 的 。 这 个 取 料
4、装 置 的 电 控 部 分 也 是 我 做的 , 电 控 部 分 主 要 是 对 这 三 个 缸 的 运 动 的 位 置 进 行 控 制 , 回 转 动 作 时 控 制 两 个 位 置 ,上 升 运 动 时 控 制 3 个 位 置 , 翻 转 运 动 时 控 制 2 个 位 置 , 一 共 控 制 七 个 位 置 。关键词: AbstractAlong with the rapid development of modern economy, the development of heavy industry is rapidly. The use of transmission device
5、 is more and more common, conveyor belt is mainly used in transmission device, and conveyor belt is material saving toward safety, energy-saving, environmental protection and development. The conveyer belt made up with rope, nylon, polyester fibers will develop rapidly, Pay more attention to improve
6、 the shock resistance, abrasion resistance, rent, properties, such as ozone resistance and service life; with various use of flame retardant belt conveyor belt, equipped with environmental protection, light of big dip Angle belt conveyor, belt, strong ascension, heat resistance, oil resistance, acid
7、 and alkali resistant conveyor, belt and various pattern of functional and special needs strong belt will develop rapidly, an important products of conveyor belt gradually formed. Meanwhile, the development of recycling economy has become the t another new topic in industry development bell.In the h
8、igh-speed development of the conveyer favorable situation, As a kind of transmission device feeding device is also the development by leaps and bounds, Feeding device is a kind of non-standard fasteners, on some special occasions, it is single in applicable scope, is generally a long-term performs a
9、 movement factory. I this roller feeder line designed by me take three main actions. Again, turn up, flip. Three actions bring roller back from the wire rope .The three movements are accomplished by hydraulic cylinder. Electric control part of the feeding device is made by me. It mainly controls the
10、 position of three cylinders, rotary movements, and two positions are controlled, rising motion, three positions are controlled, when flip- motion 2 positions are controlled, seven positions are controlled .Keywords: I目 录摘 要 .IAbstract .II第 1 章 引 言.11.1 国外输送装置发展现状.11.2 国内发展现状.21.3 发展展望.31.4 国内外带式输送机技术的差距.41.4.1 大型带式输送机的关键核心技术上的差距.41.4.2 技术性能上差距.51.4.3 可靠性、寿命上的差距.51.4.4 控制系统上差距.6第 2 章 托辊夹持装置设计.72.1 挡料盘的设计.72.2 接料盘上的的把手进行设计.9第 3 章 托辊的升降装置设计.133.1 液压缸的选取.133.1.1 液压系统工作压力的确定.133.1.2.液压缸主要尺寸的确定.