DCS系统受电及软件恢复调试方案0032

上传人:宝路 文档编号:23751782 上传时间:2017-12-03 格式:DOC 页数:7 大小:51KB
返回 下载 相关 举报
DCS系统受电及软件恢复调试方案0032_第1页
第1页 / 共7页
DCS系统受电及软件恢复调试方案0032_第2页
第2页 / 共7页
DCS系统受电及软件恢复调试方案0032_第3页
第3页 / 共7页
DCS系统受电及软件恢复调试方案0032_第4页
第4页 / 共7页
DCS系统受电及软件恢复调试方案0032_第5页
第5页 / 共7页
点击查看更多>>
资源描述

《DCS系统受电及软件恢复调试方案0032》由会员分享,可在线阅读,更多相关《DCS系统受电及软件恢复调试方案0032(7页珍藏版)》请在金锄头文库上搜索。

1、印度BALCO扩建 4300 MW燃煤电站工程DCS 系统受电及软件恢复调试方案目 录Contents1. 编制目的 Compile Purpose2. 调试范围 Scope of commissioning3. 调试前必须具备的条件 Conditions of commissioning4. 调试 步骤 Process of commissioning5. 使用工具 Tools used for test6. 注意 事项 Precautions印度 BALCO 扩建 4 x300 MW 燃煤电站工程 DCS 系统受电及软件恢复调试方案第 2 页 共 7 页1. 编制目的 Compile Pu

2、rpose为了指导及规范 DCS 带电调试工作,保证系统及设备能够安全正常投入运行, 制定本措施。The primary purpose of procedure is to guide and specify the commissioning work during energizing DCS, and make sure that the process can be put into service safely.2. 调试范围 Scope of commissioning2.1DCS 配电系统的测试。Test of DCS power distribution system.2.2

3、DCS 接地系统检查。DCS grounding system testing2.3DCS 系统双重化功能处理机冗余试验。Redundant test of DCS processors changeover.2.4DCS 系统通讯网路的贯通。Connectivity of DCS network system.2.5DCS 系统带电拷机 2448 小时。2448 hours no-load operation of the energized DCS.2.6DCS 系统软件安装DCS program download and software update2.7 本次DCS系统受电范围是所有

4、挂接在印度BALCO发电厂 (4300MW)#1 机组及公用系统 DCS 控制系统上的节点,具体如下:This energizing range covers all the nodes on the DCS of PLTU INDIA BALCO EXPANSION PROJECT-1200MW (4300MW) and common system given below:DCS 工程师站 1 台 DCS Engineer Workstation: 1 unit DCS 历史站1 台DCS Historical Workstation: 1 unit 操作员站:4 台Operating St

5、ation: 4 units 公用系统操作员站:2台Common System Operating Station: 2 unitsDCS 机 柜 :17 套DCS Cabinet: 17 set DCS 电源柜:2 套DCS Power Cabinet:2 set网 络 机 柜:2 套印度 BALCO 扩建 4 x300 MW 燃煤电站工程 DCS 系统受电及软件恢复调试方案第 3 页 共 7 页Switch Cabinet: 1 set MFT 柜:1 套MFT Cabinet: 1 set 打印机:3套Printer:3 units3. 调试前必须具备的条件 Conditions of

6、commissioning3.1 土建方面:机房门窗应安装完善,地面保持平坦通畅,如有井坑孔洞,应 敷设盖板或围栏。机房内应有充分的照明条件,并应配有适当的消防设施。空调 系统已安装完毕,并且具备投入条件。如正式空调系统无法投用,可考虑使用临 时空调以满足需要。Civil works:The doors and windows of control room should be installed completely. Control room should have flat floor, with holes and pits covered or enclosed, sufficien

7、t lighting, and adequate fire fighting facilities. Air-conditioning system should be installed, and available for operation. If formal air-conditioning system cannot be used, temporary air-conditioning can be put into service instead.3.2 安装方面:DCS 系统机柜和盘台应安装就位,供电、配电系统接线完毕且稳定的工作电源能够送至 DCS 电源开关柜,预制电缆、接

8、地系统已连接完毕。Equipment installation: DCS cabinets and panels should be installed in place. Wiring of power supply/distribution system, grounding system, and prefab cable should be completed. Reliable power can be transmit to the power supply cabinet for DCS.3.3 DCS 系统受电的相关技术资料齐全,DCS 厂家到达现场确认受电条件。Technic

9、al document required for DCS energizing should be provided completely. The representative of the DCS manufacturer should be present at site to confirm the conditions of DCS energizing.4. 调试步骤 Process of commissioning4.1 受电前的检查。Inspect before energizing.4.1.1 DCS 系统机柜检查。DCS cabinets check.4.1.1.1 DCS

10、 系统机柜内外应清洁卫生,无粉尘及杂物。DCS cabinets should be clean inside and outside, without dust or sundries.4.1.1.2 DCS 系统机柜前后以及 DCS 系统与其他系统机柜间应留有充分的工作空 间,以便调试和维护。Sufficient space for commissioning and maintenance should be left around DCS cabinets or between DCS cabinets and other system cabinets.4.1.1.3 DCS系统柜内

11、配电装置、用电装置周围应留有足够散热空间,保持通风 流畅。印度 BALCO 扩建 4 x300 MW 燃煤电站工程 DCS 系统受电及软件恢复调试方案第 4 页 共 7 页In DCS cabinets, there should be sufficient space around the power distribution devices and other heat dissipative devices for discharging heat and keeping fluid ventilation.4.1.1.4 机柜应与底座支架用绝缘板隔离,并用带有绝缘套管和绝缘垫片的螺栓紧

12、固联接。若设计为机柜接地,则无此要求。DCS cabinets must be separated from the pedestal by insulating board, and fastened by bolts with insulating bushing and gasket. No such requirement for directly-grounded cabinets.4.1.1.5 柜内冷却风扇应完整无损,电源配线应连接可靠。In DCS cabinets, cooling fan should be complete without any damage. Conn

13、ection of power wire should be reliable.4.1.2 配电检查。Inspection of power distribution4.1.2.1 严格按照设计图纸和厂家规范要求进行电源检查测试,如设计图纸和厂 家规范有冲突,应以厂家规范要求为准。Check and test of the power supply in strict accordance with the design drawings and the specifications of manufacturers. It should be based on manufacturer sp

14、ecifications, in case, whichever is conflicted.4.1.2.2 检查所有电源系统配线:对于交流电源,应注意火线、零线的连接要正 确无误;对于直流电源配线,要保证正负极性的准确连接。Check the power wiring: live lines and neutral lines are connected correctly of the AC power system, and the polarity is consistent of the DC power system.4.1.3 卡件检查。Inspection of modules

15、4.1.3.1 按照 DCS 系统厂家提供的系统安装图纸,检查确认机柜安装卡件的型号、 数量、安装位置及在卡件面板上标签是否正确。Check all of the modules mounted on the slot are in accordance with the installation drawings provided by the DCS manufacturers in type, quantity, installation location, and label of the modules.4.1.3.2 检查卡件是否插装牢靠,有关插头是否齐全。Check that a

16、ll the modules are inserted in place firm, and plugs complete.4.1.3.3 检查卡件是否有明显霉变、损坏、不洁等现象。Check all the modules for mildew, damage, impurity.4.1.4 接地检查。Grounding inspection按照设计要求,检查计算机系统信号接地和机柜接地是否符合设计要求。Check that DCS signal grounding and cabinet grounding to comply with the design 印度 BALCO 扩建 4 x300 MW 燃煤电站工程 DCS 系统受电及软件恢复调试方案第 5 页 共 7 页requirements.4.2 系统受电及软件恢复。DCS energizing and software download.4.2

展开阅读全文
相关资源
相关搜索

当前位置:首页 > 中学教育 > 教学课件

电脑版 |金锄头文库版权所有
经营许可证:蜀ICP备13022795号 | 川公网安备 51140202000112号