《ford澳大利亚CWTACART公司》由会员分享，可在线阅读，更多相关《ford澳大利亚CWTACART公司（3页珍藏版）》请在金锄头文库上搜索。
1、Facilities: Ford Environmental Wind Tunnel The Ford Australia node of ACART is located at the Ford Proving Ground in Lara, Victoria. It includes two major facilities for vehicle testing: an Emissions Test Cell and an Environmental Wind Tunnel.Both facilities are certified to ISO 9000 and ISO 14000.T
2、he new Environmental Wind Tunnel consists of a team of 6 technicians and 1 engineer. The facility specialises in, but is not limited to the following: Vehicle HVAC testing, Thermal Aero System Engineering, Trim and solar spectrum applications, Environmental cycle tests and Wheel Phase tests.The faci
3、lity is the largest environmental wind tunnel in the southern hemisphere. This high tech facility also provides a controlled and repeatable environment to develop products suitable for all global markets.The tunnel has undergone an extensive correlation program between the existing environmental cha
4、mber at the proving ground, field results and other major Ford facilities world wide. The results have been outstanding.The new Wind Tunnel facilities capabilities:Top speed: 250 km/h Temperature between -40C and +55C Temperature stability 0.25C Humidity stability 2% relative humidity Nozzle sizes 4
5、m2 and 2.7m2 Solar simulation Operating range 600 10 - 1200W/m2 Irradiation area 6m by 2.5m Irradiation uniformity 5% with irradiation area Full spectrum with UV-B filters Diurnal movement system Cirrus 48 450kW Four Wheel Drive Dynamometer: Wheelbase between 2.3m and 4.75m Maximum vehicles size 2.6
6、m tall and 2.7m wide Max. load per axle is 4500kg Inertia between 453kg and 10886kg 2 independent soak chambers with the same temperature range for cold crank and/or cold start testing Vehicle workshop with hoist ATI Vision data recording and powertrain calibration tool DiagRa MCD for On Board Diagn
7、ose and powertrain calibration Security controlled access ContactFor further information on the Ford Wind Tunnel node please contact:Mr. Martin ThurkettleSenior Diesel Test EngineerACART Site Manager Ford Node Exhaust Emissions Laboratory Ford of Australia T: +61 3 5279 5179F: +61 3 5282 2270E: W: .
8、au设施：福特环境风洞 福特澳大利亚 ACART 节点位于福特汽车试验场拉腊，维多利亚。它包括两个主要为车辆检验设施：废气测试，电池和环境风洞。 这些设备均通过 ISO 9000 认证和 ISO 14000。 新的环境风洞由一组 6 名技术员和 1 名工程师团队。该中心专门从事，但不仅限于以下内容：汽车空调测试，热航空系统工程，修剪和太阳光谱应用，环境试验和轮周期阶段的测试。 该工厂是最大的南半球环境风洞。这种高科技设备也提供了控制和可重复的环境来发展全球市场的所有产品的使用。 该隧道在经历了一个试验场现有的环境之间的广泛关系计划室，现场结果和其他主要世界各地的福特设施。该成果斐然。 新的风洞
9、设施功能： 最高时速：250 公里/小时 温度在-40 C 和 +55 温度稳定性 0.25 荤 湿度稳定 2相对湿度 喷嘴尺寸四平方米和 2.7 平方米 太阳能模拟 经营范围 600 10 - 1200 W/m2 辐射面积 6 米的 2.5 米 辐照均匀性与辐射面积 5 全光谱紫外线- B 过滤器 昼间运动系统 卷云 48“一条 450KW 四轮驱动测功机： 轴距 2.3 米之间的四点七五米 规模最大的车辆和 2.7 米高 2.6 米宽 最大。每轴负荷 4500 公斤 惯性和一零八八六公斤之间四百五十三公斤 2 个独立的浸泡商会与冷车发动和/或冷启动测试相同的温度范围 车辆维修车间葫芦 ATI 的视觉数据记录和动力系统校准工具 DiagRa 麦当劳机上动力系统的诊断和校准 安全控制的访问 联系方式 有关福特风洞节点的进一步资料，请联系： 马丁先生 Thurkettle 高级柴油测试工程师 ACART 站点管理器 - 福特节点 废气排放实验室 福特澳大利亚 电话：+61 3 5279 5179 传真：+61 3 5282 2270 电子邮件： 宽：.au
