《温度记录仪说明书样本[学习]》由会员分享,可在线阅读,更多相关《温度记录仪说明书样本[学习](7页珍藏版)》请在金锄头文库上搜索。
1、资料内容仅供您学习参考,如有不当或者侵权,请联系改正或者删除。 使用手册 OPERATION GUIDE 资料内容仅供您学习参考,如有不当或者侵权,请联系改正或者删除。 WINDOWS 98/ /XP -安装 USB数据记录仪配置软件 USB Data Logger Configuration Software Installation 1. 请把”USB 数据记录仪”安装CD放入电 脑的光驱中 , 自动运行后 , 将出现如下界 面, 单击”下一步”。 Insert the software CD into the CD drive of your computer. It will star
2、t automatically, and show this interface, then click ”Next”. 2. 阅读”重要须知”后, 选择”同意”, 进 行下一步安装 ; Read the ”IMPORTANT NOTICE ”, select ”Accept” and next. 3. 根据需求 , 选择”典型安装”或者”简 洁安装”单击”下一步”; Choose ”typical/compact installation”. Click ”Next”. 4. 选择安装路径 , 单击” 下一步” 。 默认为 : C:Program 欧诺仪器 USB温度记录 仪; Click
3、”Next”. Or change to install to another path, then Click ”Next”. Default path: ”欧诺 仪器USB温度记录仪”. 5. 单击”安装” , 开始安装。 Click ”Install”to start the installation. 资料内容仅供您学习参考,如有不当或者侵权,请联系改正或者删除。 6. 安装进度结束后 , 单击”完成”。然后 , 提示安装 USB 驱动。详细请阅读提示或者查 看”安装 USB 驱动” 。 After the process of installation closed, click ”
4、Finish ”. Then, USB driver s installation will be informed. Read hint or USB Driver Installation in detail. 资料内容仅供您学习参考,如有不当或者侵权,请联系改正或者删除。 安装 USB 驱动 USB Driver Installation 1.将 USB 数据记录仪插入电脑的USB 接口。 然后, 将会在屏幕右下角自动出现如下 提示: Insert the USB data logger into a USB port on the computer. The following scr
5、eens should automatically appear. Windows XP refers to the data logger as ”USB API”and ”USBExpress Device ”throughout this installation. 2.确保”安装 CD ”放入 CD驱动中 , 在弹 出”找到新的硬件向导” 窗口中 , 选择” 自动安装软件 ( 推荐) ”, 单击”下一 步” 。 Ensure the CD is in the CD drive. Select ”Install the software automatically (Recommende
6、d)” then click ”Next”. NOTE - A screen appears, showing files being copied to your computer. 3.出 现 安 装 对 话 框 , 默 认 安 装 路 径 : C:WINDOWSSystem32Drivers。 When the installing dialog appears, default path: C:WINDOWSSystem32Drivers. NOTE A progress bar will be displayed until the installation has been com
7、pleted 4.安装完毕 , 单击”完成”。 Installation is now complete, click ”Finish ”. 资料内容仅供您学习参考,如有不当或者侵权,请联系改正或者删除。 5.安装窗口自动关闭 , 将出现如图提示 : The window will close and you will see the following message. 6.现在即可单击”确定” , 使用 USB数据 记录仪。 You can now click ”Confirm ”, and begin using your USB data logger. 资料内容仅供您学习参考,如有不
8、当或者侵权,请联系改正或者删除。 安装电池 Battery Installation 使用 USB数据记录仪之前 , 必须插入 3.6V 1/2AA 的电池, 如下所示 : Before using the data logger you will need to insert the 3.6V 1/2AA battery provided, following the instructions below. 资料内容仅供您学习参考,如有不当或者侵权,请联系改正或者删除。 LED指示灯 LED Status Indication 颜色COLOR 闪烁 ( 次 ) G/RO 2 数据记录仪延时启
9、动。 The data logger is primed to start at a later date and time. 1 正在正常记录 , 并未超出报警上下限。 The most recently logged temperature is within the alarm levels. 1 正在记录 , 并未超出报警上下限。但存储器已满, 数据不能存储。 The data logger s memory is full, so no more readings are stored. 1 当前记录等于或低于报警下限。 The most recently logged temper
10、ature is equal to or lower than the low alarm level. 1 当前记录等于或低于报警下限。但存储器已满, 数据不能存储。 Do. But the data logger s memory is full, so no more readings are stored. 2 当前记录等于或高于报警上限。 The most recently logged temperature is equal to or higher than the high alarm level. 2 当前记录等于或高于报警上限。但存储器已满, 数据不能存储。 Do. Bu
11、t the data logger s memory is full, so no more readings are stored. 1 电池电量不足。但数据正常记录直到电压低于2.8 伏。 The battery is reaching the end of its useful life, but data logging continues until the battery voltage drops below 2.8V. 0 尚未使用 , 或未安装电池。 The logger is not being used, or the battery is not installing.