《{机械公司管理}材料的机械行为》由会员分享，可在线阅读，更多相关《{机械公司管理}材料的机械行为（55页珍藏版）》请在金锄头文库上搜索。
1、CHAPTER 2,Mechanical Behavior, Testing, and Manufacturing Properties of Materials 材料的機械行為、測試及製造特性,Working Medium of Manufacturing Process Force Heat Light Acoustics(聲音、音響) Electricity Chemistry Biology,室溫時材料之相對機械性質(Relative Mechanical Properties of Materials at Room Temperature),Tensile-Test Specime
2、n and Machine,(b),Figure 2.1 (a) A standard tensile-test specimen before and after pulling, showing original and final gage lengths. (b) A typical tensile-testing machine.,應力應變曲線（Stress-Strain Curve）,Figure 2.2 A typical stress- strain curve obtained from a tension test, showing various features.,P-
3、；- 彈性區經過放大 斜率=E 比例限、彈性限、降伏強度 Offset=0.2% 反覆循環負荷之曲線形狀 曲線下面積材料韌性 necking,E,Tension Test,Necking (Fig. 2.2) Spring back (Fig. 2.3),Engineering strain= True strain= Engineering stress= True stress=,Loading and Unloading of Tensile-Test Specimen,Figure 2.3 Schematic illustration of the loading and the un
4、loading of a tensile- test specimen. Note that, during unloading, the curve follows a path parallel to the original elastic slope.,Mechanical Properties of Various Materials at Room Temperature,Exmple,B,利於進行製造的材料 : B B材質塑性區大，降伏強度低，較易進入加工區域。 (然而A較易滿足設計需求，強度大),Ch 2.2.2 Ductility 延性,Elongation = （伸長量）
5、Reduction of area = （面積縮率、斷面縮率）,Elongation versus % Area Reduction,Figure 2.4 Approximate relationship between elongation and tensile reduction of area for various groups of metals.,Ch 2.2.4 應力-應變曲線之建立,Stress-strain curves,True strain,True stress,n : strain-hardening exponent (n=0，表示沒有加工硬化現象),Typica
6、l Values for K and n at Room Temperature,各種不同金屬在常溫下的True Stress-True Strain Curves,Figure 2.6 True stress-true strain curves in tension at room temperature for various metals. The curves start at a finite level of stress: The elastic regions have too steep a slope to be shown in this figure, and so
7、each curve starts at the yield stress, Y, of the material.,Prove = n at necking,At necking:,Ch 2.2.5,2.2.6 溫度效應 Temperature Effects on Stress-Strain Curves,Figure 2.7 Typical effects of temperature on stress-strain curves. Note that temperature affects the modulus of elasticity, the yield stress, th
8、e ultimate tensile strength, and the toughness (area under the curve) of materials.,T，則ductility， yield stress 和 modulus of elasticity (因為T，原子動能，容易克服差排障礙，延展性佳),表2.3,2.2.7變形速率的影響 Effect of Strain Rate on Ultimate Tensile Strength,2.2.7變形速率的影響 Effect of Strain Rate on Ultimate Tensile Strength,Figure
9、2.8 The effect of strain rate on the ultimate tensile strength for aluminum. Note that, as the temperature increases, the slopes of the curves increase; thus, strength becomes more and more sensitive to strain rate as temperature increases. Source: J. H. Hollomon.,strain rate tensile strength （應變硬化）
10、 直線斜率m：應變硬化敏感度指數，Temp m ,m大可以延緩necking發生，應用在金屬薄板的成形。,2.2.7變形速率的影響 Effect of Strain Rate on Ultimate Tensile Strength,超塑性（superplasticity）:某些材料在拉伸試驗時，頸縮及破壞前，發生大量的均質伸長變形量，這種變形量從幾百個百分比到兩千個百分比之間。例如：口香糖、玻璃、熱塑性塑膠、Zn-Al合金及鈦合金。,壓力：幾個ATM到3.5GPa(500KST)，液壓增加時，材料破壞時的應變量會大量增加（不容易破壞）。 脆性材料之金屬成形：液壓擠製、粉末冶金壓製。 當加工製
11、造stress超過材料破裂點，可使用下列方法避免： 加溫 加液靜壓 (Hydrostatic Pressure Effect):脆性材料加工,2.2.8 靜液壓的影響 （Hydrostatic pressure effects ),暴露在高能量輻射下：鋼料及其他種類金屬會發生降伏應力、抗拉強度及硬度會增加；延展性及韌性會減少。塑膠材料對其機械性質也有不好的影響。,2.2.9 輻射的影響（Radition effects ),桶形失真（barreling）:摩擦力,2.3 壓縮 (Compression),2.3 壓縮 (Compression),Figure 2.9 Disk test on
12、a brittle material( 陶瓷、玻璃 ), showing the direction of loading and the fracture path.,2.3 壓縮 (Compression),蒲辛格效應（Bauschinger effect 1881）:金屬受拉力進入到塑性狀態，將負荷釋放再施以壓縮應力，此時，壓縮的降伏應力值比拉伸時低許多。 應變軟化（strain softening）、作工軟化（work softening ）:因負荷的方向轉換，使降伏應力值下降。,2.4 扭 轉 (Torsion)Disk and Torsion-Test Specimens,Figu
13、re 2.10 Typical torsion-test specimen; it is mounted between the two heads of a testing machine and twisted. Note the shear deformation of an element in the reduced section of the specimen.,2.5 彎曲（撓曲）Bending （Flexure）,Figure 2.11 Two bend-test methods for brittle materials: (a) three-point bending;
14、(b) four-point bending. The areas on the beams represent the bending-moment diagrams, described in texts on mechanics of solids. Note the region of constant maximum bending moment in (b); by contrast, the maximum bending moment occurs only at the center of the specimen in (a).,硬脆材料通常都使用bending實驗量測材料
15、性質 (因為tension實驗不易進行),設備便宜且方便，所以產業界常用 Brinell (布氏硬度 1900):HB P對表面積的比值 Rockwell (洛氏硬度 1922):HR 深度 Vickers (維氏硬度 1922)：HV 深度 Knoop (克氏硬度)：HK Load極小(5-25kg)， 做微硬度測試，可用於薄脆試件。 Scleroscope (蕭氏硬度)：反跳高度、大面積 Mohs (莫氏硬度 1822)：互相摩擦， 值1（滑 石）-10（鑽石）。 Durometer 硬度測試計 Hot hardness 熱硬度,Ch 2.6 硬度（Hardness）,Hardness T
16、ests,Figure 2.12 General characteristics of hardness-testing methods and formulas for calculating hardness. The quantity P is the load applied. Source: H. W. Hayden, et al., The Structure and Properties of Materials, Vol. III (John Wiley (a) annealed metal; (b) work-hardened metal; (c) deformation of mild steel under a spherical indenter. Note that the depth of the permanently deformed zone is about one order o
