《企业管理关于单片机的智能手机充电器的设计英文版》由会员分享，可在线阅读，更多相关《企业管理关于单片机的智能手机充电器的设计英文版（11页珍藏版）》请在金锄头文库上搜索。
1、n更多企业学院： 中小企业管理全能版183套讲座+89700份资料总经理、高层管理49套讲座+16388份资料中层管理学院46套讲座+6020份资料国学智慧、易经46套讲座人力资源学院56套讲座+27123份资料各阶段员工培训学院77套讲座+ 324份资料员工管理企业学院67套讲座+ 8720份资料工厂生产管理学院52套讲座+ 13920份资料财务管理学院53套讲座+ 17945份资料销售经理学院56套讲座+ 14350份资料销售人员培训学院72套讲座+ 4879份资料n更多企业学院： 中小企业管理全能版183套讲座+89700份资料总经理、高层管理49套讲座+16388份资料中层管理学院46
2、套讲座+6020份资料国学智慧、易经46套讲座人力资源学院56套讲座+27123份资料各阶段员工培训学院77套讲座+ 324份资料员工管理企业学院67套讲座+ 8720份资料工厂生产管理学院52套讲座+ 13920份资料财务管理学院53套讲座+ 17945份资料销售经理学院56套讲座+ 14350份资料销售人员培训学院72套讲座+ 4879份资料Improvements in Battery Charger ICs Keep Pace with Rapid Increases in Mobile Handset CapabilitiesIn the era of global wireless
3、 connectivity, almost nothing is more important than keeping a smart phone or mobile Internet device charged. Expanding features on the constantly improving portable and handheld device create a major challenge for designers of battery charger ICs. High resolution screens and larger memories combine
4、 with new capabilities to tax the battery, requiring battery charger technology that is not only more efficient but also capable of managing power distribution. Optimizing power consumption to prolong battery life has always been a driving force in handheld power management. However what is changing
5、 are the efficiency expectations for charging handheld devices when they are plugged into the wall. The latest generations of device designs are using high-efficiency switching chargers in place of traditional linear chargers. Customers today continue to demand shorter charge cycles when charging th
6、eir battery. Beside higher efficiency with respect to the conventional linear chargers, one of the great advantages of using switching chargers solution is the capability to boost the charge current from what supplied by the source. This is especially important when powering off of a USB port where
7、the current available might be limited to less than 500mA. Higher charge currents equate to shorter charge cycles thus satisfying customer expectations.There are two kinds of battery chargers used in most handhelds now linear chargers and switching devices. Linear chargers have a longer history. The
8、y have typically provided a relatively efficient, simple way to charge portable devices, creating minimal noise without many external components. But as portable devices become more complex and add layers of new features, they need higher battery capacity. Linear chargers present liabilities due to
9、power dissipation, which become clear if a user wants to charge a device while using at the same time. The heat generated while simultaneously using and charging can damage the system or battery. Not a good outcome. The alternative is a switching device, or switch mode battery charger IC, that can d
10、eliver higher current levels to a battery while requiring as little power as possible. Historically, there have been some noise issues with these kinds of ICs. In addition, some early generations of switch mode devices have required several external components. However, the benefits of the switched
11、mode battery topology are clear. They include higher efficiency and lower power dissipation, along with fast charging cycles. These devices also are capable of charging from higher input voltages, which allows the use of lower cost unregulated adapters. They can increase the charging current from cu
12、rrent restricted sources. The noise from switching chargers usually comes during light load operation, particularly during preconditioning. As it decreases, many switching chargers move into an operation known as pulse skipping. In pulse skipping, the PWM frequency changes asynchronously. There have
13、 been battery charger ICs developed that supply high charge current with minimal thermal impact to the system using a switching charger, then switch into a linear charger during low current charging modes to minimize noise. This type of PWM switch mode charger with a linear mode has been a good deve
14、lopment, providing high efficiency at the full constant current (fast charge) rate. The switching charger controls large constant current charge (up to 2A) with a PWM switching regulator. It automatically moves to linear mode while the battery is preconditioning and near the end of constant voltage
15、taper charge mode, which lowers the noise while the switch mode speeds up charging. Once the charge current level dips below 300 mA, the linear mode kicks in completely and noise generated by the switching converter is eliminated. But now there are further advances. For example, an ideal solution for new handhelds is a complete charger for single cell Li+/ Polymer batteries with up to 1A charge current and advanced indication capabilities for full charge system monitoring. USB Compliant 100mA/500mA charge current settings are beneficial as are programmable pr
