《{安全管理制度}基层作业队常用安全操作规程.》由会员分享，可在线阅读，更多相关《{安全管理制度}基层作业队常用安全操作规程.（148页珍藏版）》请在金锄头文库上搜索。
1、长城钻探第一国际钻井分公司 基层作业队常用安全操作规程长城钻探第一国际钻井分公司基层作业队常用安全操作规程二零零八年四月二十一日Contents 目录1. PICKING UP AND LAYING DOWN SINGLE JOINTS （SINGLING IN / SINGLING OUT） （吊拉和甩下钻杆单根的安全操作规程）12. RUNNING IN AND LAYING DOWN DRILL COLLARS（吊拉和甩下钻铤单根的安全操作规程）43. MAKE-UP AND BREAK-OUT PROCEDURES USING RIG TONGS （使用吊钳进行钻具上扣和卸扣的安全操作
2、规程）114. SAFETY WHILE MAKING UP AND BREAKING OUT BOTTOM HOLE ASSEMBLIES AND BITS （连接和卸开下部钻具组合及钻头的安全操作规程）155. MAKING CONNECTIONS WHILE DRILLING（钻进时接单根的安全操作规程）196. WORKING IN THE DERRICK AND OVERHEAD OPERATIONS （井架工作业和高空作业的安全操作规程）247. TRIPPING（起下钻的安全操作规程）288. RUNNING SURVEY TOOL WITH RIG WIRELINE UNIT
3、（使用测斜绞车下入测斜工具的安全操作规程）389. OPERATIONS WITH TOP DRIVE SYSTEMS（顶驱的安全操作规程）4110. OPERATING THE EDDY CURRENT BRAKE（电磁涡流辅助刹车的安全操作规程）4711. SLIPPING AND CUTTING DRILLING LINE（钻井大绳滑割程序）5012. CONDUCTING LEAK-OFF TEST（地层漏失试验的安全操作规程）5413. SLOW CIRCULATING RATE SCR（ALSO SLOW PUMP RATE - SPR）（低泵速试验的安全操作规程）5714. PE
4、RFORM FLOW CHECK（溢流检查安全操作规程）5915. NIPPLE UP AND NIPPLE DOWN BOP（安装和拆卸防喷器组的安全操作规程）6216. CHANGE OUT BOP RAMS（更换闸板的安全操作规程）6917. WELL CONTROL EQUIPMENT AND MAINTENANCE REQUIREMENTS（井控设备的维护规程）7318. PRESSURE TEST PROCEDURE FOR THE HIGH PRESSURE TEST PUMP（使用高压试压泵的规程）7819. PRESSURE TESTING THE BOP AND THE B
5、OP SYSTEM（防喷器系统的试压安全操作规程）8020. SHUT-IN PROCEDURE（关井安全操作规程）8921. KILLING PROCEDURE STEP BY STEP（压井程序）9422. CLEANING MUD TANKS AFTER DRILLING H2S ZONE（钻完含硫化氢地层后清理泥浆罐的安全操作规程）9923. OPERATION AND MAINTENANCE OF THE STABBING BOARD（套管扶正台的使用和保养）10224. RUNNING CASING / LINER / TUBING（下套管、尾管和油管的安全操作规程）10525.
6、CEMENTING CASING / LINER（套管和油管固井的安全操作规程）11526. INSTALLING THE X-MAS TREE（安装采油树的安全操作规程）12727.157Picking Up and Laying Down Single Joints （Singling In / Singling Out） （吊拉和甩下钻杆单根的安全操作规程）1.SPECIAL TOOLS AND EQUIPMENT 特殊工具和设备Drillpipe lifting cap（appropriate size） 钻杆提丝（尺寸合适）Drillpipe drift （appropriate s
7、ize） 钻杆通径规（尺寸合适）Soft brush and Cleaning solvent 软刷和清洗剂 Pin and Box protectors 公、母接头护丝Kelly cock with Wrench 方钻杆旋塞和扳手Circulating sub 循环头Drillpipe dope 钻具丝扣油Tape measure 卷尺Inside BOP 内防喷器Correct size Rig tongs 大钳2. SAFETY INFORMATION 安全注意事项(1) Ensure that escape routes （ doors, stairs, etc. ） are acce
8、ssible at all times and are not obstructed by hoses, tools, etc.随时保证逃生路线可以使用（门，梯子等），不被管线、工具所阻挡。(2) Special attention must be paid while lifting the drillpipe from the catwalk onto the rig floor with the air tugger and lowering the travelling block at the same time. 当用气动绞车把钻杆从猫道吊到钻台并同时下放游车时，要特别注意。(3)
9、 Nobody is allowed to stand between the single being brought in / laid down and the joint in the rotary table. Nobody is allowed to stand with their back to the V-door, during these activities.严禁站在正在提升或甩掉的钻杆和钻盘内单根之间，严禁背对井架大门。(4) The Floormen guiding the single across the rig floor must keep feet wel
10、l clear of the pin end of the single. Winch operators must not lower singles until they are completely sure that feet are well clear of the pin end.钻台上的钻工必须注意使双脚离开单根公接头的下方，气动绞车操作者必须确认钻工双脚远离公扣下放后再下放单根。(5) Keep feet well clear of the drillpipe pin end when the drift is still in the pipe and the pipe i
11、s vertical.当通径规还在钻杆内并且钻杆处于垂直位置时，保持双脚远离钻杆公扣下方。3. STANDARD OPERATIONAL CONSIDERATIONS （DOS AND DONTS） 标准操作注意事项（1）This operation requires a Toolbox Talk, covering equipment use and positioning of personnel. 这项操作要求召开工作前安全会，会议内容包括使用的设备和人员的位置。（2）Ensure that all hoisting / lifting equipment, wires and lift
12、ing caps are in a safe condition and conforms with the current GWDC colour coding and have valid inspection certificates. 确保提升设备，钢丝绳和提丝工作状态良好，符合当前GWDC的颜色识别编号和有效的检验证书。（3）The air winch Operator shall ensure that the winch wire is moving freely in the derrick （possibly guided by pulleys） to avoid any d
13、amage to the steel structure, especially the fingerboard. 气动绞车操作者要确认气动绞车钢丝绳和井架不干涉（可以用滑轮导向），以避免损伤井架的钢结构，特别是指梁。（4）Ensure that the correct grade of pipe is being picked up. 确认吊起的钻杆级别是正确的。（5）When installing the lifting cap, ensure it is tight. 一定要旋紧提升提丝。（6）Before and after operation, count the drillpipe
14、 （DP） on the pipe rack to verify tally figures. 操作前后，数一下钻杆架上的钻杆数量，和钻杆记录表核实。（7）Any damaged DP is to be painted red （highlighting the damage） and reported to the Toolpusher for change of inventory status and transport back to base / warehouse.任何损伤的钻杆要喷上红漆，并报告带班队长变换钻具库存记录，运回基地或库房（8）When singling in, ensure pipe tally is updated as DP is being picked up. Number as per GWDC DP numbering system. 当逐根下入钻具单根时，钻杆记录表要更新，并根据GWDC的程序进行编号。（9）If pipe is 5 in diameter or greater, ta
