《(酒类资料)真空吸尘器在极端工作电压下的测试规范》由会员分享，可在线阅读，更多相关《(酒类资料)真空吸尘器在极端工作电压下的测试规范（6页珍藏版）》请在金锄头文库上搜索。
1、真空吸尘器在极端工作电压的严酷条件下的测试修订日期修订单号修订内容摘要页次版次修订审核批准2011/03/30/系统文件新制定2A/0/批准：审核：编制：真空吸尘器在极端工作电压的严酷条件下的测试1.0 Purpose / 目的To evaluate the integrity of polymeric enclosure parts of sample when operated under extreme operating voltages评估样机在极端工作电压（高和低）下进行的正常负载运行时,其马达塑料零件的安全性.2.0 Definition/概念:2.1 Thermal equil
2、ibrium-A state in which three successive temperature readings, taken at intervals of 10% of the previously elapsed duration of the test, but not less than 5 minutes, demonstrate a variation of less than 1. 热平衡-每隔前面已用的测试时间的10%的间距(但时间不少于5分钟)连续三次读数,其变化少于1时样机所达到热平衡状态2.2 Extreme operating voltages-High a
3、nd low, for this the high is 127V and low 104V 极端电压-本测试最高电压为127V,最低电压为104V.3.0 Reference Documents/参考文献:U.L.1017 CAN/CSA-C22.2 NO.243-01, dated 12-7-2001,Cl. 5.20.54.0 Equipment/设备:4.1 Frequency converter. (功率分析仪)4.2 Power analyzer(变频电源)4.3 UL test carpet (UL测试地毯)4.4 Stop watch(秒表)4.5 Data logger &
4、plug-type module. (安捷伦Datalogger和通道插板)4.6 J-type thermocouple wire. (J型温度线)4.7 Sicomet99 & Parsec Activator.( UL胶水和催化剂)5.0 General Instructions/说明:5.1 Tests may be conducted at any ambient temperature within a range of 10-40 (50-100). 测试可在1040(50100)之内的环境温度下进行.5.2 Unless otherwise noted, all tests a
5、re to be conducted with appliance connected to a 120VAC, 60Hz power source. 除非另外标注,否则所有样机都将连接在120V/60Hz电源下进行测试.5.3 All equipment used must be calibrated on an annual basis. Calibration stickers with last calibration and calibration due date must be affixed to each instrument. 使用的所有设备都必须以一年为周期进行调校.载有
6、最后调校日期和调校周期的调校粘纸必须被粘固在该仪表上.5.4 The sample is started from the chamber temperature under all test conditions. 所有测试中样机必须从室温状态起动.5.5 If the sample has “High” and “Low” speeds, the temperatures under two speeds are all measured. 如果样板有“高”“低”两种可调马达转速，须在两种转速下分别测试。5.6 If the overload protective device is no
7、t recognized as described in UL1017.20.5.5, short-circuit it out. 如果样机装有的超载保护装置诸如马达保护器，温控器未经UL1017.20.5.5所述认证，将其短接掉.6.0 Procedure/步骤:6.1 Obtain a representative sample of the appliance to be tested. 准备一台有代表性的样机用于测试.6.2 Obtain Test Results Form TTR1010 and completely fill in the information describin
8、g the sample and the equipment used prior to running the test. 用TTR1010测试结果的表格, 在测试前完整地填入样板和使用的设备的情况.6.3 Thermocouple wire is affixed to the motor enclosure: top, bottom and two sides total of four points as described in TAREGW1003. Prior to testing and after testing, the sample is connected to a 12
9、0 V, 60 Hz source of supply and operated with no load until well heated when the input to the sample is noted. 按TAREGW1003温度点接好马达胶壳上，下和两侧四个点. 测试前和测试后分别记下在120V/60Hz空载热稳定后样板的电流和功率.6.4 Adjust the test voltage to 127V. 调节测试电压为127V.6.5 Choose applicable test conditions to test the sample per the method n
10、oted in TAREGW1003. 测试方法按TAREGW1003正常温升测试进行, 不过只选取其最严酷测试状况.6.6 Adjust the test voltage to 104V, repeat 6.5. 调节测试电压为104V,重复步骤6.5.6.7 As a result of this test, there is no ignition of the thermoplastic enclosure materials. There is no warping or cracking of the thermoplastic enclosure to expose uninsu
11、lated current carrying parts, internal wiring or moving parts. 检查样机马达热塑性胶壳是否起火, 变形, 破裂以致曝露未绝缘带电零件, 内部导线和移动部件。 7.0 Results/结果:7.1 Use the corresponding Test Results Form TTR1010 to report all numerical results as the information described below. 使用TTR1010测试结果的表格, 除报告所有数字结果外, 还有下列描述的数据.7.2 Clearly and
12、 completely describe all parts that are part of this evaluation. Include all model numbers, manufacturing date codes, materials, plastic part revision letters, and modification status. 清楚并完整地描述本评估的所有零件, 包括所有型号名称, 材料和塑料零件改版符号.7.3 Clearly and completely describe all special conditions of the test (i.e. Was the test performed in exact accordance with the test procedure or were there special variations). 清楚并完整地描述所有测试的特殊条件(即按照测试程序实际进行的测试或特殊的变改).
