《ABAQUS显隠转换分析.doc》由会员分享，可在线阅读，更多相关《ABAQUS显隠转换分析.doc（64页珍藏版）》请在金锄头文库上搜索。
1、.2.1 Transferring results between Abaqus analyses: overviewProducts: Abaqus/Standard Abaqus/Explicit Abaqus/CAE References “Transferring results between Abaqus/Explicit and Abaqus/Standard,” Section 9.2.2 “Transferring results from one Abaqus/Standard analysis to another,” Section 9.2.3 “Transferrin
2、g results from one Abaqus/Explicit analysis to another,” Section 9.2.4 *IMPORT *IMPORT ELSET *IMPORT NSET *IMPORT CONTROLS *INSTANCE “Transferring results between Abaqus analyses,” Section 16.6 of the Abaqus/CAE Users ManualOverviewAbaqus provides the capability to import a deformed mesh and its ass
3、ociated material state from Abaqus/Standard into Abaqus/Explicit and vice versa. This capability is particularly useful in manufacturing problems; for example, the entire sheet metal forming process (which requires an initial preloading, forming, and subsequent springback) can be analyzed. In this c
4、ase the initial preloading can be simulated with Abaqus/Standard using a static procedure and the subsequent forming process can be simulated with Abaqus/Explicit. Finally, the springback analysis can be performed with Abaqus/Standard.Abaqus also provides the capability to transfer desired results a
5、nd model information from an Abaqus/Standard analysis to a new Abaqus/Standard analysis or from an Abaqus/Explicit analysis to a new Abaqus/Explicit analysis, where additional model definitions may be specified before the analysis is continued. For example, during an assembly process an analyst may
6、first be interested in the local behavior of a particular component but later is concerned with the behavior of the assembled product. In this case the local behavior can first be analyzed in an Abaqus/Standard or Abaqus/Explicit analysis. Subsequently, the model information and results from this an
7、alysis can be transferred to a second Abaqus/Standard or Abaqus/Explicit analysis, where additional model definitions for the other components can be specified, and the behavior of the entire product can then be analyzed.For this capability to work, the same release of Abaqus/Explicit and Abaqus/Sta
8、ndard must be run on computers that are binary compatible.ABAQUS可以从隐式计算结果到显示计算进行分析，该问题在求解一些问题是非常有用的，例如薄钢的锻造过程（经历预加载，成形和回弹），该分析预加载可以通过std分析，锻造过程可以通过XPT进行分析，最后回弹可以再用std进行分析。ABAQUS也提供了从隐式分析到隐式分析和从显示分析到显示分析，例如可以先对感兴趣的局部构件进行分析，分析完成后，在对整个结构作分析，前部的分析结果可以传到后面的整体分析中。Saving the analysis resultsThe restart fil
9、es from the original analysis contain the analysis results that are transferred from Abaqus/Standard or Abaqus/Explicit. Obtaining restart files is described in more detail in “Writing restart files” in “Restarting an analysis,” Section 9.1.1; brief summaries are provided below. By default, Abaqus/S
10、tandard does not write any restart information and Abaqus/Explicit writes results at the beginning and end of each step.Saving results from Abaqus/StandardIf the results are to be imported from an Abaqus/Standard analysis, the results from the original Abaqus/Standard job must be written to the rest
11、art (.res), analysis database (.mdl and .stt), part (.prt), and output database (.odb) files. You can specify the increments at which restart information will be written. Restart information is always written at the end of a step in addition to the requested increments whenever you request restart d
12、ata in Abaqus/Standard.Input File Usage: *RESTART, WRITE, FREQUENCY=n保存分析结果重启动文件包含了之前分析的信息，关于重启动的描述参阅“Writing restart files” in “Restarting an analysis,” Section 9.1.1；下面做简要介绍，默认情况下，std不保存重启动文件，xpt在每个分析部开始和结束步保存重启动文件。Std结果保存如果想从std分析后获得结果，原始的std分析必须保留重启文件（.res），分析数据(.mdl and .stt)，PART(.prt),和输出数据(.
13、odb)文件，用户可以指定具体的重启位置，重启信息除了在请求的位置输出外在每一分析步的最后也将输出。Input File Usage: *RESTART, WRITE, FREQUENCY=nAbaqus/CAE Usage: Step module: OutputRestart Requests: enter n in the Frequency column for each stepXpt结果保存如果想要从某一时刻输入xpt分析的结果，则必须在原始的结果文件中保存.abq状态文件，状态文件重启文件数据文件，PART文件和结果文件共同用来从xpt分析后的结果作为输入。可以具体指定是否精确的
14、时间输出xpt重启文件，因为xpt会在每个分析步的最后给出重启文件。Input File Usage: Use the following option to request results at the increments ending immediately after each time interval:*RESTART, WRITE, NUMBER INTERVAL=n, TIME MARKS=NOUse the following option to request results at the exact time intervals:*RESTART, WRITE, NUMB
15、ER INTERVAL=n, TIME MARKS=YESAbaqus/CAE Usage: Step module: OutputRestart Requests: enter n in the Number Interval column; click to check the Time Marks column for each step if you want the results written at the exact time intervalsSaving results from Abaqus/ExplicitIf the results are to be importe
16、d from an Abaqus/Explicit analysis, the results from the original Abaqus/Explicit job must be written to the state (.abq) file at the time when transfer of the state of the deformed body is required. The state (.abq), restart (.res), analysis database (.stt), package (.pac), part (.prt), and output database (.odb) files will be used for importing the results from Abaqus/Explicit.You c
