《2020（技术规范标准）GRCGRG技术规范更新版》由会员分享，可在线阅读，更多相关《2020（技术规范标准）GRCGRG技术规范更新版（130页珍藏版）》请在金锄头文库上搜索。
1、广州孚姆新材料科技股份有限公司 GRC GRG FRP TCP技术规范 2014更新版 目录 Section 1 GRC Section 2 GRG Section 3 FRP Section 4 TCP Section 5 General Painting and Coating Specifications SECTION1 GLASS FIBER REINFORCED CONCRETE GFRC GRC 玻璃纤维加强水泥 GFRC GRC PART 1 GENERAL 第 1 部分 简介 1 01 RELATED DOCUMENTS 1 01 相关文件 A Drawings Condit
2、ions of the Contract and Division 1 Specifications sections apply to work of this section A 图纸 合同条款及第一部分说明章节适用于本章内容 1 02 SUMMARY 1 02 概要 A Section Includes Glass Fiber Reinforced Concrete GFRC part fabrication and installation as scheduled at the end of this section and as shown on the architectural
3、 drawings A 章节内容包括 如本章结尾提到及建筑图纸所示 玻璃纤维加强水泥 以下简称为 GFRC 或 GRC 制造及安装 1 03 REFERENCE STANDARDS 1 03 参考标准 A ASTM C947 Test Method for Flexural Strength A ASTM C947 弯曲强度测试方法 B ASTM E 84 Test Method for Surface Burning Characteristics of Building Materials B ASTM E 84 建筑材料表面燃烧特性测试方法 C MNL 128 Range of Prem
4、ix Properties Recommended to PCI C MNL 128 PCI 标准推荐的预混料属性的范围 D ASTM E136 Test method for Surface Burning Characteristic of Building Materials D ASTM E136 建筑材料表面燃烧特性测试方法 1 04 SUBMITTALS 1 04 提交材料 A Samples submit six 6 each 300mm x 300mm and 20 50mm x 50mm samples demonstrating finish to be supplied
5、finish per contract A 样板 提交 6 件 300mm x 300mm 和 20 件 50mm x 50mm 的样板 该样板需展示 表面效果 按合同 B Shop Drawings Submit shop drawings delineating all details required for fabrication and installation Shop drawings to indicate the necessary blocking and attachment to the building or framing as required to suppor
6、t and secure the GFRC material and any material attached to GFRC Framing details and structural support of framing is the responsibility of the GFRC manufacturer installer and it is to be engineered and sealed by contractor subcontractor and noted accordingly in the material supply contract and shop
7、 drawings B 施工图 提交描述所有生产及安装细节的施工图 施工图需表明必要的安装块 框架和 连接物 用于支撑和稳固 GFRC 材料或其他固定在 GFRC 上的材料 框架细节和框架结构 支撑由 GFRC 生产方负责 由承包方 安装方进行工程设计 并在材料供应合同和施工图纸 安装细节中标注清楚 1 05 QUALITY ASSURANCE A All GFRC parts shall match approved samples A 所有 GFRC 产品必须与通过的样板相符 B All GFRC parts and additional framing required due to n
8、on structural walls e g brick or others will be Installable according to details submitted in shop drawings All support and framing systems must be engineered by an engineer able to place his seal for the structure and design of all GFRC panels and installation systems as he sees them acceptable and
9、 certified fit for purpose B 根据提交的施工图 所有 GFRC 件及非结构墙后补墙 如砖或其他 必须可安装 所有 支撑及结构系统必须由结构工程师设计 计算其结构 包括所有 GFRC 板及其安装系统 机构工程师须盖章证明结构可行可达到目的 C Pigments C 色粉 1 Coloring Admixture ASTM C979 synthetic mineral oxide pigments or colored water reducing admixtures temperature stable nonfading and alkali resistant
10、1 着色添加剂 ASTM C979 合成氧化物矿物色粉或者着色减水添加剂 耐温度 不褪色 抗碱 性 2 Coloring Admixture not to exceed 10 percent of cement weights 2 着色添加剂 比重不能超过水泥重量的 10 1 07 DELIVERY STORAGE AND HANDLING 1 06 运输 仓储及操作 A All materials shall be protected during fabrication shipment site storage and erection to prevent damage to the
11、finished work from other trades Store materials inside a well ventilated area away from uncured concrete and masonry and protected from weather moisture soiling abrasion and extreme temperatures A 所有材料必须在生产 运输 工地存储及安装过程加以保护 以防止其他工种损坏已完 成的工作 将材料存储于通风良好的地方 远离未固化的水泥和砖石 并保护其不受天气 潮湿天气 脏污 磨损 弯曲及极端天气影响 B P
12、rotect fabrications from damage by retaining or duplicating shipping protection in place until installation B 保护产品从运输至安装过程不受损坏 C Damage Responsibility Except for damage caused by others the installer is responsible for chipping cracking or other damage to GFRC parts after delivery to the job site an
13、d until installation is complete and inspected and approved by the contractor architect and FORM 1 07 WARRANTY 1 07 产品保证 A Warrant fabrications to be free from defects due to materials and workmanship A 保证产品没有材料及工艺方面造成的缺陷 PART 2 PRODUCTS 第 2 部分 产品 2 01 FABRICATED PRODUCTS 2 01 产品制造 A GFRC will be fa
14、bricated with a proprietary blend of cementitious minerals aggregates polymers and glass fibers to achieve a typical range of physical properties shown in Section 2 03 and all PCI standards whichever is greater A GFRC 按照专有配方制造 其中有胶凝矿物 粒料 聚合物和玻璃纤维达到指定范围的 物理特性 符合第 2 03 条和所有 PCI 标准 两者取其最高标准 2 02 PHYSIC
15、AL PROPERTIES 2 02 物质性能 Property Value 属性值Test Method Result 测试方法及结果 Barcol Hardness 巴氏硬度 ASTM D 2583 56 Points Compression 压缩力 ASTM C 39 10 810 psi CTE Average 热膨胀系数平均值 ASTM D 696 8 0 x 10 6 in in F Density 密度 ASTM D 792 132 5 lbs cu ft Flammability Class I Materials ASTM E 84 0 Flame 50 Smoke 可燃性
16、1类材料 ASTM E 84 0 Flame 50 Smoke Flexural Strenght 弯曲强度 ASTM D 790 2 630 psi Tensile 拉伸强度 ASTM D 638 1 500 psi 2 03 FINISH 2 03 表面处理 A Surface Texture Exposed side Smooth or as indicated on drawing A 表面质地 暴露面 光滑或依图纸所示 B Finish Smooth surface or to match approved color and texture Parts determined to be painted must be clean primed and ready to finish prior to the application of an acceptable paint system B 表面处理 光滑表面或使用经核准的颜色和质地 确定需要喷漆的产品在喷漆前做好 清洁 上好底漆 准好接受面漆 Please note that non integral colored
