《使用说明书h3cs3100v2系列以太网交换机快速安装指南_5pw100_整本手册》由会员分享，可在线阅读，更多相关《使用说明书h3cs3100v2系列以太网交换机快速安装指南_5pw100_整本手册（3页珍藏版）》请在金锄头文库上搜索。
1、 Tool list 工具参考 Before installation wear an ESD preventive wrist strap and make sure that the wrist strap has a good skin contact and is well grounded 在以下安装交换机的过程中 操 作者需佩戴防静电腕带 请确保防静电腕带已经正确接地并与皮肤良好接触 Mounting the switch to a rack 安装交换机到机柜 Introduction to installation accessories 安装附件介绍 The installat
2、ion tools are not provided with the switch Prepare them by yourself 交换机不随机提供安装工具 请用户根据实际安装需求自己准备安装工具 Phillips screwdriver 十字螺丝刀 Needle nose pliers 尖嘴钳 ESD preventive wrist strap 防静电腕带 Claw hammer 羊角锤 Spanner 扳手 Drill 电钻 Marker 记号笔 Grounding cable 地线 Cage nut and M6 screw user supplied 浮动螺母和M6 螺钉 自备
3、Standard front mounting bracket 标准前挂耳 Wall mounting bracket 壁挂挂耳 Magnet and countersunk head screw optional 永磁铁和沉头螺钉 选配 Bail latch 电源线卡钩 Rear mounting bracket and load bearing screw 后挂耳和承重螺钉 Guide rail and M5 self tapping screws optional 滑道和M5自攻螺钉 选配 Wall anchor user supplied 拉爆膨胀螺栓 自备 Foot pads 脚垫
4、M4 screw M4 螺钉 1 Long front mounting bracket optional 加长型前挂耳 选配 Flathead screwdriver 一字螺丝刀 Installation methods安装方式 Width宽度 Depth深度 Use front mounting brackets 前挂耳安装 Use front and rear mounting brackets 前挂耳和后挂耳配 合安装 Use front mounting brackets and guide rails 前挂耳和滑道 配合安装 11 8in 300mm 17 3in 440mm 16
5、 5in 420mm 17 3in 440mm 11 8in 300mm Long front mounting brackets 加长型前挂耳 Method 1 Using only front mounting brackets 仅使用前挂耳安装 Install standard front mounting brackets 安装标准前挂耳 Install long front mounting brackets安 装加长型前挂耳 Select a method based on the size of your switch and the rack 根据交换机和机柜的尺寸 选择其中一
6、种 1 Install cage nuts to the square holes of the rack 安装浮动螺母到机柜方孔条 1U 23 Method 2 Using front and rear mounting brackets 前挂耳和后挂耳配合安装 Install the load bearing screw 安装承重螺钉 Install the front mounting bracket 安装标准前挂耳 1 Install cage nuts to the square holes of the rack 安装浮动螺母到机柜方孔条 1U 2 2 Mounting the s
7、witch to a workbench 安装交换机到工作台 Only switches having four installation holes on the left and right sides for installing mounting brackets support wall mounting Do not apply wall mounting to devices not meeting the installation requirement Otherwise a falloff or bodily injury may occur 仅每个侧面都有四个螺孔用于安装
8、壁挂挂耳的交换机支持壁挂式安装 请不要在不具备 安装条件的设备上使用壁挂方式进行安装 否则可能会出现脱落或造成人身伤害 2 Stick the foot pads to the appropriate positions on the switch bottom 粘贴脚垫到交换机底部 1 Wall mounting 壁挂安装 Method 3 Using front mounting brackets and slide rails 前挂耳和滑道配合安装 1U 2 4 Install cage nuts to the square holes of the rack 安装浮动螺母到 机柜方孔条
9、 Install slide rails 安装滑道 Install the standard front mounting bracket 安装标准前挂耳 3 1 Mount the rear mounting brackets to the square holes on the rear post of the rack 安装后挂耳到机柜后方孔条 4 3 3 43 Magnet mounting 磁吸安装 Only switches having blind nuts in the dents of the switch bottom support magnet mounting Do
10、not apply magnet mounting to devices not meeting the installation requirement Otherwise a falloff or bodily injury may occur 仅底部四角圆形印压区 域内有安装螺孔的交换机支持磁吸式安装 请勿在不具备安装条件的设备上使用磁吸 方式进行安装 以免出现脱落或造成人身伤害 Put the switch at a stable place free from vibrations or shocks and avoid installing the switch at a high
11、 place because bodily injury or device damage may occur in case of a falloff in the case of poor surface magnet mounting may not be reliable 请勿将交换机置于有振动 冲击及不稳定的地方 也勿将交换机置于过高处 否则有可能造成人身伤害或设备损坏 如果安装地点表面状态不佳 还有可能影响磁 吸安装的可靠性 Avoid frequently moving the desk mounted switch because such movements may dama
12、ge the surface coating 当在办公桌上用磁吸方式固定交换机时 请勿人为往 复推动 否则会引起接触面涂层的损坏 Fix the external cables firmly to avoid falloff which may result in personal injuries or device amage 安装时要注意交换机外接线缆的固定 避免因外接线缆过重而引起交换 机脱落 以致造成人身伤害或设备损坏 Install the wall mounting bracket 安装壁挂专用挂耳 12 Measure the distance between holes on
13、 the mounting bracket and mark holes on the wall for the mounting points 测量挂耳 上螺孔 左右孔和上下孔 间 距离 并在墙壁上标记打孔位 置 横向水平 纵向垂直 Mount the switch to the wall壁挂安装 Before drilling holes on a concrete or wood wall make sure that there is no electrical wire behind the wall where holes are to be drilled to avoid bo
14、dily injury 在水泥墙或木质墙上打孔前 请确认打孔处没有墙电 以免造成人身伤害 Mount the switch to the wall with the network interfaces facing downwards 请注意将 交换机的网口朝下进行壁挂 4 Connecting the power cable 连接电源线 Before connecting the power cable connect the grounding cable and make sure that the s w i t c h is correctly grounded 在连接电源线前 需
15、先连接保护地线 保证交换机 正确接地 Connect the power cable to the switch first and then to the power supply system to avoid bodily injury 连接电源线时 请先完成电源线与交换机侧的连接 再进行电 源线与供电系统的连接 以免造成人身伤害 Supplied power cable and the installation modes depend on your device model 各型号 标配的电源线及安装方式可能不同 请按照实际情况进行安装 Connect the AC power c
16、able 连接交流电源线 Connecting the grounding cable 连接保护地线 Connect the other end of the grounding cable to a grounding device另一端连接 接地设备 OT terminal OT端子 Connect the OT terminal of the grounding cable to the switch OT端子与交换机相连 Without a bail latch无电源线卡钩情况 To mount the switch vertically make sure the network interfaces of the switch face downwards 采用磁吸垂直安装交换机时 请将交换机网口朝下 Keep floppy disks and magnetic cards away from the magnets to avoid erasure of any information 勿将磁铁与软盘 磁卡等产品接近 否则会引起产 品存储内容被擦除 Keep comput
