《Quick_start_manual_Profibus（S7-300）》由会员分享，可在线阅读，更多相关《Quick_start_manual_Profibus（S7-300）（24页珍藏版）》请在金锄头文库上搜索。
1、 PROFIBUS Encoder With SIEMENS S7 300 Quick Start HanDong Product management department Disclaimer The content of this document serves informative purposes only and is not binding Pepperl Fuchs endeavors that all information on this document is accurate However Pepperl Fuchs does not guarantee that
2、the information is complete accurate faultless useful for a certain purpose or available at any time Pepperl Fuchs also reserves the right to change or to delete the information from the document without announcement Pepperl Fuchs is not liable for damages irrespective of their nature incurred by th
3、e use or the non use of the information except where Pepperl Fuchs has caused the damage intentionally Pepperl Fuchs document partly contains information on third parties product documents Pepperl Fuchs is not responsible for the content or the existence of third parties documents and is especially
4、as long as Pepperl Fuchs does not have positive knowledge of their contents not liable for damages irrespective of their nature incurred by the use or the non use of third parties documents The copyright of all contents on this document created by Pepperl Fuchs is exclusively reserved for Pepperl Fu
5、chs It is prohibited to copy or otherwise use these contents especially information snap shots in any form without the written consent of Pepperl Fuchs Pepperl Fuchs does not intentionally infringe copyrights of third parties However Pepperl Fuchs cannot generally guarantee that copyrights of third
6、parties are not infringed Apart from that please note that third party s document on to which this document is based may be protected by copyrights Pepperl Fuchs collects processes or uses personal data only as far as the user reveals it and if it is necessary for the constitution organization in co
7、ntent or the alteration of a contract Pepperl Fuchs Trading co ltd ShangHai PMD Encoder BU Table of Contents 1 Purpose 1 1 Module used 1 2 Software used 1 3 Gsd file for the encoder 1 4 Related document 2 Hardware configuration 2 1 Connection of the signal and power supply lines 2 2 Bus member addre
8、ss 2 3 Adjust the terminal resister 3 Simartic manager Siemens software configure 3 1 Create a new project 3 2 Configure the hardware of the project 3 3 Monitor the position value of the encoder 3 4 The description of the status bit 4 An example for the profibus encoder 1 Purpose This documentation
9、explains how to configure the connection between Siemens PLC and a Pepperl fuchs encoder 1 1 Module used Description Model No Version Siemens S7 300 Power supply 6ES7 307 1EA00 0AA0 S7 300 CPU 6ES7 315 2AF03 0AB0 V1 1 PVM58N encoder PVM58N 011AGR0BN 1213 Version 2 2 1 2 Software used Simartic manage
10、r 1 3 Gsd file for the encoder You can download from the website Http www pepperl Process as below Step1 Enter the website of Pepperl fuchs Step2 Fill the blank Product Search with PVM58 then click enter Step3 Click the Multiturn absolute encoder PVM58 in the page Step4 find the Gsd File in the web
11、Left click the 1830846 zip Step5 Download and save 1830846 zip file Step6 Extract the 1830846 zip file 1 4 Related document Description Provider Art Step 7 programming manual Siemens LAD FBD STL program for S7 300 Siemens Profibus Encoder manual Pepperl Fuchs 2 Hardware configurations 2 1 Connection
12、 of the signal and power supply lines Note the power supply line can only be connected once no matter to which terminal If the encoder is fit as a terminal device then the terminating resistor that is integrated into the device must be switched into the circuit This is done with the slide switch in
13、the connection hood 2 2 Bus member address The PROFIBUS member address can be set with decimal rotary switches in the Connection hood The valency x 10 or x 1 is specified on the switch Possible addresses are between 1 and 99 Each address can occur only once in the system 2 3 Adjust the terminal resi
14、ster 3 Simartic manager Siemens software to configure the hardware 3 1 Create a new project Step 1 Double click the logo then you will open the windows of Simartic manager Step 2 Click the Then you will look at the window as below In the Name type the name of the new project then click OK 3 2 Config
15、ure the hardware of the project Step1 right click the name of the project go to the insert new object and click the Simatic 300 station Step 2 click the SIMATIC 300 1 Step 3 double click the hardware open the windows of hardware configuration Step 4 configure the slot in the hardware windows Double
16、click the rail pay attention to the type of Rack 300 Step 5 drag the module of power supply to the slot1 Step6 drag the CPU module to the slot 2 and create a profibus DP bus in the windows Click the new botton Set the transmission rate and Profibus profile then Click OK Step 7 configure the encoder Go to the options and click on the Install New GSD Find GSD file that download from the website then click the open button You can find the encoder of Pepperl Fuchs in the list Step 8 Configure the en
