《汽车专业的毕业设计》由会员分享，可在线阅读，更多相关《汽车专业的毕业设计（23页珍藏版）》请在金锄头文库上搜索。
1、 专业外文翻译材料系 别 南京机电学院 专 业 汽车检测与维修技术 班 级 汽修 1003 学生姓名 岳祥龙 学 号 1101513240 指导教师 张锦龙 2013 年 4 月无锡科技职业学院毕业设计（论文）专业外文翻译材料i目 录第一部分 专业外文翻译材料原文1第二部分 专业外文翻译材料译文12参考文献21无锡科技职业学院毕业设计（论文）专业外文翻译材料1专业外文翻译材料原文EnginesCylinder BlockThe cylinder block is the largest past of the engine.Its upper section carries the cylin
2、ders and pistons.Normally,the lower section forms the crankcase,and supports the crankshaft.It can be cast in one piece from grey iron.Or it can be alloyed with other metals like nickel or chromium.The iron casting process begins by making up the shapes of what will become water jackets and cylinder
3、s as sand cores which are fitted into moulds.The stops there parts becoming solid iron during casting.Molten iron is poured into sand moulds that are formed by patterns in the shape of the block.After casting,core sand is removed through holes in the sides and ends,leaving spaces for the cooling and
4、 lubricant passages.There holes are sealed with plugs.The casting is then machined.Cylinders are bored and finished,surfaces smoothed,holes drilled and threads cut.All cylinder blocks are made with ribs,web and fillets to provide rigidity but also keep weight to a minimum.Cylinder Block Construction
5、As more manufacturers try to make vehicles lighter and more fuel efficient,more and more engine blocks are being cast from aluminium.A block made of aluminium alloy is lighter than if it were made of cast iron.So if two engines are generating the same power,the alloy version would have a better weig
6、ht-to-power ratio than the cast alloy version.Aluminium alloy blocks are made by various casting processes,including pressure casting.Another method is gravity casting,where the molten metal is poured into molds.Cast iron liners are usually used in the cylinders of aluminium blocks,and sometimes in
7、cast-iron blocks.Some sleeves are cast into the block.Grooves on the outside form a key that stops any movement in the cylinder.They also increase surface area to assist heat transfer from the sleeve to the block.Some blocks dont need liners.They can be made of wear resistant material that makes a h
8、ard-wearing surface for the pistons and piston rings.Or the cylinder bore may have some sort of surface treatment to make it hard-wearing.When the cylinders,block and crankcase are all cast together,it is called a 无锡科技职业学院毕业设计（论文）专业外文翻译材料2monoblock construction.A horizontally-opposed block has a spl
9、it crankcase.The two engine blocks are joined together by the flanges of the crankcase.In air-cooled engines,the cylinders are usually made as separate parts,then bolted to the same crankcase.Each cylinder has cooling fins.Theyre often machined to give uniform thickness and allow free flow of air.Pi
10、stonsThe piston,with its connecting rod and bearing,transfers the force of the combustion and expansion of the power stroke to the crankshaft.The piston itself,its rings,and the piston pin,also known as the gudgeon pin,are together called the piston assembly.The cutaway shape on this piston allows i
11、t to clear the counterweights on this rotating crankshaft.The connecting rod connects the piston to crankshaft. It is fastened to the piston at its little end,by a piston or gudgeon pin.The big end of the connecting rod has a detachable cap,and carries 2 halves of the big end bearing.The big end is
12、attached to the crankshaft at the crankpin journal.Cylinder SleevesCylinder sleeves are used in engine blocks to provide a hard-wearing material for pistons and piston rings.The block can be made of one kind of iron thats light and easy to cast,while the sleeve uses another kind that is better able
13、to stand up to wear and tear.There are three main types of sleeves-dry,flanged dry,and wet.The dry sleeve can be cast in or pressed into a new block, or used to recondition badly-worn or damaged cylinders that cant easily be re-bored.Its a pressed fit in its bore in the cylinder blocks.Its wall is a
14、bout 2mm thick.Its outer surface is in contact with the block for its full length.Its top finishes flush with the top of the block and can hardly be seen.Once in place,dry sleeves become a permanent part of the cylinder block.A flanged,dry sleeve is like a normal dry sleeve,but a flange at the top f
15、its into a recess in the surface of the engine block.Its not a tight fit and it can be replaced if its worn.With a wet sleeve,the outer surface is part of the waterjacket around the cylinder.Its called wet because it has coolant against its outer surface.This helps speed up heat transfer between the
16、 sleeve and coolant.The sleeve is sealed at the top to prevent coolant leaks.This stops coolant entering the combustion chamber,and the bottom of the 无锡科技职业学院毕业设计（论文）专业外文翻译材料3crankcase.A flange at the top of the sleeve fits into a recess in the block.The lower end has 1 or 2 neoprene sealing rings.With coolant in direct contact with the cy
