《M162~M166【安装施工记录】【GHOE】》由会员分享，可在线阅读，更多相关《M162~M166【安装施工记录】【GHOE】（6页珍藏版）》请在金锄头文库上搜索。
1、海阳核电工程施工总承包部CNF Haiyang NPP Construction Project Managemen环轨直径误差测量记录Surveying record for the tolerance of rail diameter记录代码Record code记录编号Record No页码Page页码/总页数Page No./Total pages检查试验计划编号/版本ITP NO./Rev.图纸号/版本Dwg. No./Rev.堆号/Reactor No.厂房/Building区域/Area系统号/System No.记录项目Recorded Item技术要求6.4mmTechnic
2、al requirement6.4mm6096mm长度范围内轨道偏心误差 The tolerance of rail eccentricity in the length of 6096mm编号No.最大值Max.最小值Min.偏差值Offset value编号No.最大值Max.最小值Min.偏差值Offset value备注Remarks以90270线逆时针测量Survey anti-clockwise from the line of 90270.整体偏心误差Integral eccentricity tolerance技术要求9.5mm Technical requirement9.5
3、mm最大值Max.最小值Min.偏差值Offset value施工班组/Construction Team技术人员/Technical Personnel质检人员/QC Personnel签字/Signature日期/Date签字/Signature日期/Date签字/Signature：日期/ Date：海阳核电工程施工总承包部CNF Haiyang NPP Construction Project Managemen轨道接口间隙测量记录Surveying record for the gap of rail interface记录代码Record code记录编号Record No页码Pa
4、ge页码/总页数Page No./Total pages检查试验计划编号/版本ITP NO./Rev.图纸号/版本Dwg. No./Rev.堆号/Reactor No.厂房/Building区域/Area系统号/System No.记录项目Item编号No.技术要求Technical requirement测量值Surveying value备注Remarks轨道接口间隙Rail interface gap0-0.5mm最后间隙Final gapN/A6.4-12.7mm备注：具体详图参见附图2，螺栓编号见附图3Remarks: See the attached figure 2, and s
5、ee attached figure 3 for bolt numbering施工班组/Construction Team技术人员/Technical Personnel质检人员/QC Personnel签字/Signature日期/Date签字/Signature日期/Date签字/Signature：日期/ Date：海阳核电工程施工总承包部CNF Haiyang NPP Construction Project Managemen轨道安装中心测量记录Surveying record for the centre of rail记录代码Record code记录编号Record No页码P
6、age页码/总页数Page No./Total pages检查试验计划编号/版本ITP NO./Rev.图纸号/版本Dwg. No./Rev.堆号/Reactor No.厂房/Building区域/Area系统号/System No.编号NoXY编号NoXY编号NoXY编号NoXY轨道安装中心点计算坐标The coordinates of the center point for rail installation by calculationX轴坐标X positionY轴坐标Y position备注：具体详图参见附图2，螺栓编号见附图3Remarks: See the attached f
7、igure 2, and see attached figure 3 for bolt numbering施工班组/Construction Team技术人员/Technical Personnel质检人员/QC Personnel签字/Signature日期/Date签字/Signature日期/Date签字/Signature：日期/ Date：海阳核电工程施工总承包部CNF Haiyang NPP Construction Project Managemen主梁水平度测量记录Measuring Record of Levelness for Girder 记录代码Record code记
8、录编号Record No页码Page页码/总页数Page No./Total pages检查试验计划编号/版本ITP NO./Rev.图纸号/版本Dwg. No./Rev.堆号/ Reactor No.厂房/Building区域/Area系统号/System No.测量情况 Measuring Situation主梁A水平度误差Levelness Error of Girder A长度方向上水平度误差Levelness Error in Length Direction技术要求Technical Requirement 1/4”(6.35mm)实际误差Actual Error宽度方向上水平度误
9、差Levelness Error in Width Direction技术要求Technical Requirement 1/16”(1.59mm)实际误差Actual Error主梁B水平度误差Levelness Error of Girder B长度方向上水平度误差Levelness Error in Length Direction技术要求Technical Requirement 1/4”(6.35mm)实际误差Actual Error宽度方向上水平度误差Levelness Error in Width Direction技术要求Technical Requirement 1/16”(
10、1.59mm)实际误差Actual Error施工班组/Construction Team技术人员/Technical Personnel质检人员/QC Personnel签字/Signature日期/Date签字/Signature日期/Date签字/Signature：日期/ Date：海阳核电工程施工总承包部CNF Haiyang NPP Construction Project Managemen环吊桥架测量记录Measuring Record of Bridge Frame for Polar crane记录代码Record code记录编号Record No页码Page页码/总页数
11、Page No./Total pages检查试验计划编号/版本ITP NO./Rev.图纸号/版本Dwg. No./Rev.堆号/ Reactor No.厂房/Building区域/Area系统号/System No.测量情况Measuring Situation主梁间距Space between Girders技术要求 Technical Requirement: 23-214”(7061.26.35mm)序号Serial No.实际测量Actual Measurement备注Remarks序号Serial No.实际测量Actual Measurement备注Remarks对角线误差Diagonal Error技术要求 Technical Requirement: 3.175mm实际测量Actual Measurement1#对角线长度 1# Diagonal Length2#对角线长度 2# Diagonal Length差值施工班组/Construction Team技术人员/Technical Personnel质检人员/QC Personnel签字/Signature日期/Date签字/Signature日期/Date签字/Signature：日期/ Date：6精品文档
