《ccnae2charpter5》由会员分享，可在线阅读，更多相关《ccnae2charpter5（13页珍藏版）》请在金锄头文库上搜索。
1、Take Assessment - ERouting Chapter 5 - CCNA Exploration: Routing Protocols and Concepts (Version 4.0)Time Remaining: 1窗体顶端Refer to the exhibit. All routers in the exhibit are running RIP v1. The network administrator issues theshow ip routecommand on router A. What routes would appear in the routing
2、 table output if the network is converged? (Choose two).R 192.168.2.0/24 120/1C 192.168.2.0/24 120/1R 10.10.3.0/24 120/0C 10.10.3.0/24 120/1R 10.10.1.0/24 120/2R 10.10.1.0/24 120/3窗体底端2窗体顶端Refer to the exhibit. Router1 and Router2 are running the RIPv1 protocol. The network administrator configures
3、the commandnetwork 10.1.0.0on Router1. What network will Router1 advertise to Router2?10.1.0.0/1610.1.0.0/810.0.0.0/1610.0.0.0/8窗体底端3窗体顶端Refer to the exhibit. The network that is shown is running RIPv1. The 192.168.10.0/24 network was recently added and will only contain end users. What command or s
4、et of commands should be entered on Router1 to prevent RIPv1 updates from being sent to the end user devices on the new network while still allowing this new network to be advertised to other routers?Router1(config-router)#no router ripRouter1(config-router)#network 192.168.10.0Router1(config-router
5、)#no network 192.168.10.0Router1(config-router)#passive-interface fastethernet 0/0Router1(config-router)#passive-interface serial 0/0/0窗体底端4窗体顶端Which of the following would be the correct command sequence to enable RIP on Router B for all connected networks?RouterB#router ripRouterB(router)#network
6、210.36.7.0RouterB(router)#network 220.17.29.0RouterB(router)#network 211.168.74.0RouterB(config)#router ripRouterB(config-router)#network 198.16.4.0RouterB(config-router)#network 211.168.74.0RouterB(config-router)#network 199.84.32.0RouterB(config)#configure router ripRouterB(config-router)#network
7、210.36.7.0RouterB(config-router)#network 199.84.32.0RouterB(config-router)#network 211.168.74.0RouterB(config)#router ripRouterB(config-router)#network 198.16.4.0RouterB(config-router)#network 210.36.7.0RouterB(config-router)#network 211.168.74.0RouterB(config)#router ripRouterB(config-router)#netwo
8、rk 198.16.4.0RouterB(config-router)#network 210.36.7.0RouterB(config-router)#network 220.17.29.0窗体底端5窗体顶端Which command will display RIP activity as it occurs on a router?debug ip ripshow ip routeshow ip interfaceshow ip protocolsdebug ip rip configshow ip rip database窗体底端6窗体顶端Which command or set of
9、 commands will stop the RIP routing process?RouterB(config)#router ripRouterB(config-router)#shutdownRouterB(config)#router ripRouterB(config-router)#network no 192.168.2.0RouterB(config)#no router ripRouterB(config)#router no rip窗体底端7窗体顶端Refer to the exhibit. RIPv1 is running on all three routers.
10、All interfaces have been correctly configured with addresses in the address ranges that are shown. Which route would you see in the routing table on router CHI if the routers are configured with the commands that are displayed in the exhibit?192.168.0.4/30192.168.0.0/24192.168.0.0/16192.168.0.32/27窗
11、体底端8窗体顶端The following line was displayed in the output of theshow ip routecommand.R 192.168.3.0/24 120/3 via 192.168.2.2, 00:00:30, Serial0/0What is the value of the routing metric?3122030120窗体底端9窗体顶端What will happen if an interface IP address is entered for the address portion of thenetworkcommand
12、in a RIPv1 configuration instead of a network address?The router will reject the command.A route to the host address will be added to outgoing RIP updates.A route to the host address will be added to the routing table.All interfaces in the same classful network as the configured address will be incl
13、uded in the RIPv1 routing process.窗体底端10窗体顶端What are three characteristics of the RIPv1 routing protocol? (Choose three.)supports the use of VLSMuses hop count as a metricconsiders a metric of 16 as infinityhas an administrative distance of 110 by defaultincludes the destination IP address and subne
14、t mask in routing updatescalculates metrics using the Bellman Ford algorithm窗体底端11窗体顶端Refer to the exhibit. Router1 is running RIPv1. What command was entered into Router1 to configure the gateway of last resort?no auto-summaryip default-network 0.0.0.0ip default-gateway 10.0.0.0ip route 0.0.0.0 0.0.0.0 S0/0/1窗体底端12窗体顶端Refer to the exhibit. All routers that are shown are running the RIP routing protocol. All unknown IP traffic must be forwarded to the ISP. What router or set of routers are recommended to have both a default route and thedefault-information originatecommand issued
