《罗杰斯-高频板材》由会员分享，可在线阅读，更多相关《罗杰斯-高频板材（2页珍藏版）》请在金锄头文库上搜索。
1、Advanced Circuit Materials Division 100 S. Roosevelt Avenue, Chandler, AZ 85226 Tel: 480-961-1382 Fax: 480-961-4533 Data Sheet RO4400 Series Prepreg Data Sheet RO4450Band RO4450F Prepreg RO4000 dielectric materials have long been used in combination with FR-4 cores and prepreg as a means to achieve
2、a performance upgrade of standard FR-4 multi-layer designs. RO4003C , RO4350B , and RO4000 LoPro glass reinforced hydrocarbon/ceramic laminates have been used in layers where operating frequency, dielectric constant, or high-speed signal requirements dictate the need for high performance materials.
3、FR-4 cores and prepreg are still commonly used to inexpensively form less critical signal layers. The RO4400 prepreg family is comprised of four grades based on the RO4000 series core materials, and are compatible in multi-layer constructions with either RO4003C, RO4350B or RO4000 LoPro laminates. A
4、 high post-cure Tg (280C / 536F ) makes RO4400 series prepreg an excellent choice for multi-layers requiring sequential laminations as fully cured RO4400 prepregs are capable of handling multiple lamination cycles. In addition, FR-4 compatible bond requirements (177C/350F) permit RO4400 prepreg and
5、low flow FR-4 prepreg to be combined into non-homogenous multi-layer constructions using a single bond cycle. RO4450F prepreg has demonstrated improvement in lateral flow capability, and is becoming the first choice for new designs or as a replacement in designs that have difficult fill requirements
6、. Each of the RO4450B and RO4450F prepregs are recognized by Underwriter Laboratories with the UL-94 flame rating, and are compatible with lead-free processes. Data Sheet The information contained in this data sheet and processing guide is intended to assist you in designing with Rogers circuit mate
7、rials and prepreg. It is not intended to and does not create any warranties, express or implied, including any warranty of merchantability or fitness for a particular purpose or that the results shown on this data sheet and processing guide will be achieved by a user for a particular purpose. The us
8、er is responsible for determining the suitability of Rogers circuit materials and prepreg for each application. Prolonged exposure in an oxidative environment may cause changes to the dielectric properties of hydrocarbon based materials. The rate of change increases at higher temperatures and is hig
9、hly dependent on the circuit design. Although Rogers high frequency materials have been used successfully in innumerable applications and reports of oxidation resulting in performance problems are extremely rare, Rogers recommends that the customer evaluate each material and design combination to de
10、termine fitness for use over the entire life of the end product. These commodities, technology and software are exported from the United States in accordance with the Export Administration regulations. Diversion contrary to U.S. law prohibited. The world runs better with Rogers. and the Rogers logo
11、are licensed trademarks of Rogers Corporation. RO4000, RO4400, RO4003C, RO4350B, RO4450B, RO4450F and LoPro are licensed trademarks of Rogers Corporation. 1999, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012 Rogers Corporation, Printed in U.S.A, All rights reserved. Revised 01/30/2012 -0
12、112-CC Publication #92-150 Rogers UL file number is E102763B. Typical Values RO4450B, RO4450F, Prepreg PROPERTY TYPICAL VALUES DIRECTIONUNITSCONDITIONTEST METHOD RO4450BRO4450F Thickness3.6 (0.91)4 (0.101)4 (0.101)Zmils (mm)- Dielectric Constant , er 3.30 0.053.54 0.053.52 0.05Z-10GHz - 23C IPC-TM-6
13、50 2.5.5.5 Dissipation Factor, tan d 0.0040.0040.004Z-10GHz-23C IPC-TM-650 2.5.5.5 Dielectric Strength100010001000ZV/mil23C/50% RH IPC-TM-650 2.5.6 Volume Resistivity 9.26 X 1079.26 X 1078.93 X 108 -Mcm23C/50% RH IPC-TM-650 2.5.17.1 Surface Resistivity 3.82 X 1073.82 X 1071.03 X 107X,Y M23C/50% RH I
14、PC-TM-650 2.5.17.1 Thermal Conductivity 0.600.600.65ZW/m/K80CASTM C518 Moisture Absorption 0.0100.050.09-% 48 hrs immersion 0.060” sample temperature 50C ASTM D570 Tg280280280-C TMA -60C - 300C 10C/min IPC-TM-650 2.4.24 Td390390390-C TGAASTM D3850 Density1.801.861.83-gm/cm323CASTM D792 Copper Adhesi
15、on 4.0 (0.70)4.9 (0.86)4.0 (0.70)Z pli (N/mm) oz. EDC After Solder Float IPC-TM-650 2.4.8 Coefficient of Thermal Expansion 19 17 60 19 17 50 19 17 50 X Y Z ppm/C-55 to 280C IPC-TM-650 2.4.41 ColorWhiteWhiteWhite- FlammabilityV-0V-0V-0UL94 Lead-Free Process Compatible YesYesYes Typical values are a r
16、epresentation of an average value for the population of the property. For specification values contact Rogers Corporation. STANDARD THICKNESS:STANDARD SIZE: RO4450B, 0.0036 (0.091mm), 0.004, (0.101mm) RO4450F 0.0040” (0.101mm) 24X18” Sheets (610mm X 457mm) Contact Customer Service for other available sizes.
