《smd-led-3528正白光规格书样板(6000-6500k)》由会员分享，可在线阅读，更多相关《smd-led-3528正白光规格书样板(6000-6500k)（10页珍藏版）》请在金锄头文库上搜索。
1、SPECIFICATIONPart No.：CUSTOMER APPROVEDAPPROVED BYCHECKED BYPREPARED BYDescriptions: Our PLCC SMD LEDs offer high-intensity light output and a wide viewing angle and low power consumption in an standard package.The white LED is available in the range of color temperature of 2300K to 15000KFeatures:
2、l TOP LED Typel Size（mm）:3.5*2.8*1.9l Emitting Color: Whitel Wide view angle at 120l SMT packagel Suitable for all SMT assembly and soldering methodl Pb-free Reflow soldering applicationl RoHS CompliantApplications: l Light Stripsl LCD Backlightl Decorative lightingl Indicatorsl Interior automotivel
3、 Illuminationsl Mobile PhonesAbsolute Maximum Ratings (Ta = 25) ItemsSymbolAbsolute maximum RatingUnitForward Current(DC)IF30mAPeak Forward Current*IFP100mAPower DissipationPD120mWOperation TemperatureTopr-20 +75Storage TemperatureTstg-30 +80Reverse VoltageVR5VSoldering TemperatureTsolReflow Solderi
4、ng:250/10sec*Pulse width1msec duty1/10 Typical Electrical & Optical Characteristics ( Ta = 25) ItemsSymbolConditionMin.Typ.Max.UnitForward VoltageVFIF = 20mA2.8-3.6VReverse CurrentIRVR = 5V5uAChromatic Coordinates(X,Y)IF = 20mA-(0.31,0.33)-Color TemperatureCCTIF = 20mA60006500KLuminous FluxVIF = 20m
5、A7lmLuminous IntensityIVIF = 20mA1800mcd50% Power Angle2IF = 20mA-120-DegNotes: MaterialItemReflectorWireEncapsulateChipMaterialPPAGoldSiliconeInGaN/A12O3Package Dimensions(unit:mm)Notes: All dimensions in mm tolerance is 0.1mm unless otherwise noted.Typical Electrical/Optical Characteristics Curves
6、(Ta=25 Unless Otherwise Noted)Taping Dimension(unit:mm)Notes:(1) Quality:2000Pcs/reelReel PackagingPart NO: IV: xxx-xxx mcdVF: XX-XX VCCT: XXXX-XXXX QTY:2000PCSLot. NO: XXXXXPart NO:IV: xxx-xxx mcdVF: XX-XX VCCT: XXXX-XXXX QTY:2000PCSLot. NO: XXXXX Notes:The boxes are not water-resistant, and they m
7、ust be kept away from waterPrecautions for use:1. StorageTo prevent moisture absorption into SMD LEDs during the transportation and storage, the LEDs are packed in a moisture-barrier bag. Desiccants and a humidity indicator are packed together with the LEDs as secondary protection The shelf life of
8、LEDs stored in the original sealed bag at 40 and 90% RH is 12 months. Baking is required if the shelf life has expired Before opening the packaging, check for air leaks in the bag. After the bag is opened, the SMD LEDs must be stored at 30 and 60% RH. Under these conditions, SMD LEDs must be used wi
9、thin 24 hours. If the LEDs are not within 24 hours after removal from the bag, baking is required Take the material out of the packaging bag before baking. Do not open the oven door frequently during the baking process.2. Soldering(1) Manual soldering with a soldering Iron Use a soldering iron of le
10、ss than 25 watts is recommended. The iron temperature must be kept below 315And soldering time no more than 2 seconds. The epoxy resin of an SMD LED should not contact the tip of the soldering iron. No mechanical stress should be exerted on the resin portion of an SMD LED during soldering. Handling
11、of an SMD LED should be done only when the package has been cooled down to below 40 Reflow solderingTemperature profileSolder=Sn63-Pb37Solder= Pb-FreeAverage ramp-up rate:4/sec.maxAverage ramp-up rate:4/sec.maxPeak preheat temperature:100-150Peak preheat temperature:100-150preheat time:100seconds.ma
12、xpreheat time:100seconds.maxramp-down rate:6/sec.maxramp-down rate:6/sec.maxPeak temperature:230Peak temperature:250Time within 5 of actual peak temperature=10 sec. maxTime within 5 of actual peak temperature=10 sec. maxDuration above 183 is 80 sec. maxDuration above 217 is 80 sec. maxSMD LED should
13、 not be modified after soldering. If modification cannot be avoided, the modification must be pre-qualified to avoid damage to the SMD LEDs.Reflow soldering should not be done more than one timeNo stress should be exerted on the package during soldering.(3) Recommend Soldering pad design(unit=mm)3.
14、Static Electricity Static Electricity and surge voltage damage the LEDs. So it is recommended that an ESD wrist band, ESD shoe strap or an anti-electrostatic glove be used when handling the LEDs. All devices, equipment and machinery must be properly grounded4. Others Reverse voltage should not exceed the absolute maximum rating on the data sheet. The colour of the LEDs is changed slightly an operating current and thermal. This device should not be used in any type of fluid such as w
