《【2017年整理】端盖落料拉深冲孔复合模》由会员分享，可在线阅读，更多相关《【2017年整理】端盖落料拉深冲孔复合模（37页珍藏版）》请在金锄头文库上搜索。
1、1端盖落料拉深冲孔复合模学 院、系： 机械工程学院 7摘 要随着中国工业不断地发展，模具行业也显得越来越重要。本文针对端盖的冲裁工艺性和拉深工艺性，分析比较了成形过程的三种不同冲压工艺（单工序、复合工序和连续工序） ，确定用一幅复合模完成落料、拉深和冲孔的工序过程。介绍了端盖冷冲压成形过程，经过对端盖的批量生产、零件质量、零件结构以及使用要求的分析、研究，按照不降低使用性能为前提，将其确定为冲压件，用冲压方法完成零件的加工，且简要分析了坯料形状、尺寸，排样、裁板方案，拉深次数，冲压工序性质、数目和顺序的确定。进行了工艺力、压力中心、模具工作部分尺寸及公差的计算，并设计出模具。还具体分析了模具的
2、主要零部件（如凸凹模、卸料装置、拉深凸模、垫板、凸模固定板等）的设计与制造，冲压设备的选用，凸凹模间隙调整和编制一个重要零件的加工工艺过程。列出了模具所需零件的详细清单，并给出了合理的装配图。通过充分利用现代模具制造技术对传统机械零件进行结构改进、优化设计、优化工艺方法能大幅度提高生产效率，这种方法对类似产品具有一定的借鉴作用。关键词：端盖；模具设计；复合模；拉深冲孔8ABSTRACTWith Chinas industries continue to develop and die industry is also becoming increasingly important. Based
3、 on the Cover of the stamping process and the deep drawing process, Comparative analysis of the process of forming three different stamping process (single processes, complex processes and continuous processes) confirm completion of a composite model blanking, drawing processes and punching process.
4、 On the cover of the cold stamping process, right after the Cover of the mass production, quality components, and the use of structural components of the analysis, research, in line with lower performance prerequisite to the identification of stampings, Stamping method used to complete the processin
5、g components, and a brief analysis of the blank shape, size, layout, the Conference Board, the number of Drawing, stamping processes in nature, number and sequence determination. For the process, the center of pressure, the die size and the tolerance of the calculation, design mold. Also analyzes th
6、e mold of the main components (such as punch and die and dump devices, drawing punch, slates, Punch plate, etc.) design and manufacturing, stamping equipment selection, punch-gap adjustment and establishment of a vital parts machining process. Die requirements set out a detailed list of parts, and g
7、ives a reasonable assembly. By fully utilizing modern manufacturing technology to mold traditional mechanical parts for structural improvements, design optimization, Process optimization methods can greatly enhance production efficiency, the method of similar products have some reference.Keywords: C
8、over; Mold design; Composite molding; Drawing Punch主要符号表IX目 录1 分析零件的工艺性 12 确定工艺方案 22.1 计算毛坯尺寸 22.2 确定是否要压边圈 32.3 计算拉深次数 32.4 确定工艺方案 43 主要工艺参数的计算 53.1 确定排样、裁板方案 53.2 计算工艺力、初选设备 63.2.1 计算工艺力 6（1）落料力 6（2）冲孔力 7（3）推件力 7（4）拉深力 7（5）压边力 83.2.2 拉深功的计算 93.2.3 初选压力机 93.2.4 计算压力中心 103.2.5 计算凸、凹模刃口尺寸及公差 104 模具的结构设计 124.1 模具结构形式的选择 124.1.1 模架的选用 124.1.2 模具的闭合高度 134.2 模具工作部分尺寸计算 134.2.1 落料凹模 134.2.2 拉深凸模
